Gidday,
Looking for load data on the 50gr TTSX using BM2. Can’t seem to find it documented anywhere.
Any advice appreciated.
Cheers
Printable View
Gidday,
Looking for load data on the 50gr TTSX using BM2. Can’t seem to find it documented anywhere.
Any advice appreciated.
Cheers
https://www.barnesbullets.com/wp-con...mingtonWeb.pdf
Found by searching "Barnes 223 load data".
Hodgdon Benchmark = ADI BM2.
Thank you. Didn’t know they were same powder when I’d seen that earlier .Quote:
Originally Posted by Pommy
Just use 50 grain data and work up..they are awesome projectiles.
Greetings,Quote:
Originally Posted by Pommy
Only data for Barnes projectiles should be used for loading them as they are longer and harder than the same weight lead core projectiles and will give higher pressure.
GPM.
My understanding was that the Barnes relief rings actually lower pressure?
Their published data appears to be right up there with the warmest cup and core data in manuals.
Greetings @Tahr,
I don't have any actual experience with Barnes projectiles as they are beyond my cheap skate price. Comparing their book data for the 150 grain in the .308 they seem to get the same velocity with 1.5 grains less powder than I have chronographed with AR2206H in a 24" barrel.
GPM.
I suppose it doesn't matter much really so long as you begin conservatively.Quote:
Originally Posted by grandpamac
I did find this though: https://www.google.com/search?client...UTF-8&oe=UTF-8
My loads are the same with them as with cup n core...if not hot rodding to begin with you should be fine.
Greetings,Quote:
Originally Posted by Tahr
I also found that the Nosler 129 grain LRAB gave almost 100 fps more velocity than the Hornady 129 grain soft point in the 6.5-06 with everything else the same so the heavy jacketed projectiles seem to push up velocity and pressure as well as the mono's. I relly should try some I suppose.
GPM.
27gr BM2. Use 26gr with 53gr TSX. Brutal and accurate.
Have you been reading NZ hunter?
@Greg Duley should try some 80gr ELDM or 77gr TMK ..! Obviously no good for NZTF work, but outside that you'll be pleasantly surprised out at the ranges where the non-lead bullets stop working
Have a look at the data from Charliehorse above. More powder with the ttsx in the max loads compared to the cup and core in same wt. A bit of a surprise there.
Sent from my iPhone using Tapatalk
No I hadn’t till about 10 minutes ago. Turns out I get 5 free articles if using the ZINIO app to view the magazine online. Good read.Quote:
Originally Posted by gimp
I was talking to a mate who has some association with DOC and their non toxic ammo supply.
I’m going to OIA the cost of their non toxic centrefire ammo because I don’t believe the number he told me they pay per round to procure.
I always want to have a tutu after reading many a thread online about many of the copper projectiles and sending them at warp speed.
I am shooting the 45 TSX bullet at 3400 fps.
(Extraordinarily inaccurate until I found how deep to seat the bullet and now all it shoots are half inch groups. It hates everything until you get the right OAL and then out of nowhere it shoots little groups.)
I have not actually shot an animal with a 45g TSX yet. Too many bullets I keep mucking with. It is only a 1:12 twist CZ527 so it will shoot everything nicely but Barnes bullets it wont shoot the 53 TTSX, but it will the 50g TSX.
What've you heard? High or low?Quote:
Originally Posted by McNotty
53gr need a fast twistQuote:
Originally Posted by John Duxbury
High.Quote:
Originally Posted by gimp
