Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Ammo Direct


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 18
Like Tree19Likes

Thread: 25cal hp casting oops

  1. #1
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129

    25cal hp casting oops

    So, tonight was 25cal night, dug out my NOE 25 cal 4 cavity mold, it casts 3 @ 120gr, 1is a hp, and 1 @ 85gr, smoked up the cavity and the hp pin, was casting really really nicely then……pin comes out of handle, I found the smallest Phillips tip screw drive and tried to tighten it, no joy! I am assuming that it has a tiny grub screw, but to be honest it could also be pressed in? Any one had a similar issue and how did you get around it. Ive a couple HP projectiles cast so I can put them back in the mold and get the appropriate depth , put the pin in and then the handle back on and use a thin nail punch and drive the retaining pin/screw in good and propper or is there a plan B?

    Name:  0AAF29A7-C1F0-44A7-B685-42D0AC48CA73.jpeg
Views: 378
Size:  2.60 MB
    Name:  94D09418-7EFD-4A18-9EE4-F03CD718A5B3.jpeg
Views: 399
Size:  2.56 MB
    Phil_H likes this.

  2. #2
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    They ought to be fun, but I would like to cast more of them!
    Name:  70426AD1-79A1-4B72-A567-422704E3EB61.jpeg
Views: 392
Size:  2.06 MB
    veitnamcam, Micky Duck and Phil_H like this.

  3. #3
    Member Micky Duck's Avatar
    Join Date
    Apr 2015
    Location
    Geraldine
    Posts
    24,797
    they look like fun alright....wallaby medicine
    Tertle and Carbine like this.

  4. #4
    Member
    Join Date
    Jun 2016
    Location
    Perth
    Posts
    72
    Do they come out of the mould that clean or have you tidied them up?

  5. #5
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    That’s as they fell!
    Micky Duck and SkiHunt like this.

  6. #6
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    Quote Originally Posted by SkiHunt View Post
    Do they come out of the mould that clean or have you tidied them up?
    Good prep, hot mold and well smoked, NOT from a candle, I have a mix that I try to keep to and add a little solder……and a shit ton of luck

    Name:  D695BAC6-64BE-4FD4-9C2A-782763C3C962.jpeg
Views: 360
Size:  3.62 MB
    SkiHunt and Jhon like this.

  7. #7
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    But I need to fix the HP pin!

  8. #8
    Member Micky Duck's Avatar
    Join Date
    Apr 2015
    Location
    Geraldine
    Posts
    24,797
    talk to Robert....he will KNOW,we will just be guessing.

  9. #9
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    So 6am and I fixed it, small grub screw, I’ll find a small Allan key to really get it in propper, just wondering is there a heat resistant loc tight?

  10. #10
    Member Micky Duck's Avatar
    Join Date
    Apr 2015
    Location
    Geraldine
    Posts
    24,797
    gasket goo????

  11. #11
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    im going to run the mold today and see how it goes, i will use extremely dry thin macrocarpa to smoke the mold again, ill make sure the pin is hot too, hopefully that ought address the issue, but id like to make up a few HP 120's to start new load development

  12. #12
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    Quote Originally Posted by Micky Duck View Post
    gasket goo????

    im also wondering if i delicately remove a little metal on the pin and make a slot for the grub srew to locate and sit in that might help?

  13. #13
    Member Cordite's Avatar
    Join Date
    May 2017
    Location
    NZ Mainland (Dunedin)
    Posts
    5,531
    With the generous meplat maybe HP is overkill. Maybe just use them as they turned out?

    The tiny bit extra weight up front should also improve stability, and not having the HP means one less potential source of bullet assymmetry.
    An itch ... is ... a desire to scratch

  14. #14
    Member Tertle's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch NZ
    Posts
    1,129
    Quote Originally Posted by Cordite View Post
    With the generous meplat maybe HP is overkill. Maybe just use them as they turned out?

    The tiny bit extra weight up front should also improve stability, and not having the HP means one less potential source of bullet assymmetry.
    I had given that some thought, my thinking was that this doesn’t have the same controlled expansion that a jacketed projectile offers? Plus moving the center of balance back just a tad may help what little aerodynamics of the home made lead cast im making, I could and may be well off but I have a 30 cal that I have used in the past that proved, fruitful when I hade used it, it’s a mini trash can, I had used some earlier versions of what we had affectionately named the 6.5 cruise missile for the Carcano, but that punched through (everything) with little deformation, admittedly that could well be my fault in the lead mix, but good comment, well worth me going back to some of my old school reloading books,

    This is the trashcan latest iteration

    Name:  8A125F91-9855-4C6C-875D-671EFFCE3C40.jpeg
Views: 247
Size:  2.66 MB
    Micky Duck likes this.

  15. #15
    Member
    Join Date
    Dec 2013
    Location
    Tokoroa
    Posts
    1,221
    My NOE moulds have a different setup for the HP I order the RG2 and RG4 style, And I never smoke them I give them a good cleaning in hot soapy water
    and heat them to 350 to 400 F and cool a couple of times then cast it takes a couple of casting sessions to cure the mould properly,
    Not sure how to fix your pin but Loc Tight do make a heat cured product for engine studs.
    Robert.
    Tertle and Micky Duck like this.

 

 

Similar Threads

  1. Oops...
    By Survy in forum Firearm Safety
    Replies: 18
    Last Post: 04-02-2021, 10:45 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!