Printable View
Getting this set up today with scope and bipod rail fitted.
Looking forward to running some 162s ELDMs and RE26.
https://uploads.tapatalk-cdn.com/202...3981322a9e.jpg
https://uploads.tapatalk-cdn.com/202...f38f5aa964.jpg
https://uploads.tapatalk-cdn.com/202...001a61d5c4.jpg
https://uploads.tapatalk-cdn.com/202...3fe5898ea1.jpg
https://uploads.tapatalk-cdn.com/202...a309aa01f3.jpg
https://uploads.tapatalk-cdn.com/202...e3b004ff71.jpg
Sent from my iPhone using Tapatalk
God damn that front stud is a PITA. Mine flogged out in the stock so I had to do the same as you have done. The honeycomb in the forend was not centered at the stud so I ended up making a larger aluminium insert and epoxy glued it in, filling the voids. Being a bedded barrel also made it harder.
Yep it is! The Montana stock is too with a foam inner. The Forbes is just a void. I did the best I could - I used a spare bolt half inserted into the keeper to locate it in the stock so I could easily get the securing bolts seated.
Just an observation (in case the original photo led folk to think otherwise) is that alignment should be confirmed at two positions, and not with a single placement. The diagram at the side shows how misalignment could still be possible if checked at only one position. Best results are with the tools set as far forward as the rings allow, and then as far back. The rings are only positioned correctly when alignment occurs at both positions.
Somewhere else on the Forum was a thread for posting home-made reloading and related tools, and these would be a valuable addition if not there already. They make for a simple home project for anyone who can get half–an–hour's access to a lathe, and are really effective — more so than using a single bar. 25.4mm and 30mm diameter will be off–the–shelf, but 34mm will have to be turned down as part of the project I imagine.
Attachment 258804
Nice.
I have a 280 AI that I built on a Sako L61R action with a Douglas barrel 24".
It shoots very well. I have a great load with Nosler Accubond 160 gr over N560. I get 3000 fps which is the Nosler book load.
It is on Buy Sell. Please PM me for photos etc.
Can do that with a half decent laser and some farting about too. Or a... Well there's many ways to skin the cat on this one.
One very simple way, ( found by an Australian I believe!), is revert your two pins so that actually the flats are facing each other’s , it will tell you straight away if there is a mis alignement and if the rings are on the same plane or not.Quote:
Originally Posted by Puffin
It works better with a perfect flat face rather than with a slight chamfer.
Testing with H2 hybrid brake and 175gn LRABs all with 58.5gn RE26. Seating depths 3.351 (mag length) (2854fps), 3.331 (2871fps), 3.270 (2817fps). All speed is down with shortest COAL the group is by far the best.
https://uploads.tapatalk-cdn.com/202...18cfbf95f3.jpg
https://uploads.tapatalk-cdn.com/202...700e92b200.jpg
https://uploads.tapatalk-cdn.com/202...6e022fec41.jpg
https://uploads.tapatalk-cdn.com/202...72d3bbe27c.jpg
https://uploads.tapatalk-cdn.com/202...09f0c12958.jpg
https://uploads.tapatalk-cdn.com/202...f3c739c8d3.jpg
https://uploads.tapatalk-cdn.com/202...38ae01fded.jpg
https://uploads.tapatalk-cdn.com/202...d1898937a4.jpg
Sent from my iPhone using Tapatalk
175gn LRAB, 3.27 COAL, 2817fps.
https://uploads.tapatalk-cdn.com/202...21f7bcad5e.jpg
Sent from my iPhone using Tapatalk
Managed to get a little N560 (still hoping for some from a forum member that offered).
Tried with with A-Tec brake but didn’t go well. So tried with H2 hybrid suppressor. 162gn ELDMs with 59.5gn and 3.27” COAL. 2nd shot was a flyer(?) but next 2 went into first hole.
61.5gn 3.330” COAL 3rd shot went into first shot hole.
Should I just call it done at 59.5gn? Seemed very mild.
https://uploads.tapatalk-cdn.com/202...8a5d372ff3.jpg
https://uploads.tapatalk-cdn.com/202...2372c6ae76.jpg
https://uploads.tapatalk-cdn.com/202...4ccdacb40a.png
https://uploads.tapatalk-cdn.com/202...af658b8d0b.png
Sent from my iPhone using Tapatalk
61gn N560 3.225-3.330 COAL 162gn ELDM.
2 shots at 400y (slightly low) after sighting in, 2 at 600y (slightly high).
Not sure my ballistics chart is bang on point but for hunting should be ok.
https://uploads.tapatalk-cdn.com/202...1ca39f343f.png
https://uploads.tapatalk-cdn.com/202...859fe455d9.jpg
https://uploads.tapatalk-cdn.com/202...5dcc118038.jpg
https://uploads.tapatalk-cdn.com/202...570b34b437.png
Sent from my iPhone using Tapatalk
Above shot with the wee A-Tec brake.
*3.325-3.330 COAL.
Very nice, how much jump at that COL?
https://uploads.tapatalk-cdn.com/202...3840a133e1.pngQuote:
Originally Posted by chainsaw
Sent from my iPhone using Tapatalk
3.404 is touching with the ELDM.Quote:
Originally Posted by chainsaw
