Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Ammo Direct Terminator


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 17
Like Tree5Likes

Thread: 7mm rem mag

  1. #1
    Member
    Join Date
    Feb 2013
    Location
    Vic Australia
    Posts
    33

    7mm rem mag

    Hi guys,

    I have just bought a new 7mm barrel for my R8. I was wondering what ppl loads were?? I have loaded up some 154gr with 70gr Ar2225. I have started with an oal of 3'270 see how it goes?? Im not a massive wrap on the sst but had no amax and only light 120gr ttsx so this was it.

  2. #2
    Lovin Facebook for hunters kiwijames's Avatar
    Join Date
    Feb 2012
    Location
    Hawkes Bay
    Posts
    7,205
    Running 72g 2225, Norma brass and 162AMax in a R93. Jumping about 0.025" IIRC. I think I might find more speed with 2217 but cannot be bothered as already doing 2990.
    7mmsaum likes this.
    The range of what we think and do is limited by what we fail to notice. And because we fail to notice that we fail to notice, there is little we can do to change; until we notice how failing to notice shapes our thoughts and deeds

  3. #3
    Member Carpe Diem's Avatar
    Join Date
    Feb 2014
    Location
    The foothills of the Waitak's
    Posts
    1,212
    Running 162 Amax at 62.9Gr of IMR 7828 in both Federal and Norma Brass, runs about 2895 ave with the suppressor. Its a T3 lite so the jump to fit the round in the mag is 0.112" and the COAL is 3.330. Note over the SAMI spec but considering the jump... meh! (after a wee mini meltdown when I realised - Thnx 7mmSaum for the advice)

    Shoots real well sub .5 moa depending on how fast your firing the rounds, as it tends to walk up and to the left at 10.30 hrs Barrel heat is the real accuracy killer for this load.

    I also run a factory 140gr Norma Barnes TTSX round as my first round in the bush for close work. Devastating and POI is consistently only about a inch lower than the Amax at 100m.

    Just a couple of thoughts...

  4. #4
    Lovin Facebook for hunters kiwijames's Avatar
    Join Date
    Feb 2012
    Location
    Hawkes Bay
    Posts
    7,205
    FYI I have yet to load anything in my two Blaser barrels that doesn't like to be jumped. Don't know why but just touching always shoots like shit in my barrels.

  5. #5
    Member Bryan's Avatar
    Join Date
    Dec 2011
    Location
    Tauranga
    Posts
    873
    I run two loads in my T3 7mm RM. IIRC they are:

    0-250yds: 160 Nosler Accobond, Norma brass, Fed 215GM primers, AR2217 (Can't remember amount), seating to fit mag, MV: 2800fps. Shoots honest 3/4 - 1.0 MOA groups.

    250yds+: 162 Hornady Amax, Norma brass, Fed 215GM primers, 75.5gr AR2225 (Compressed), 0.020" jump (single feed), MV: 3050fps. Shoots 1/2 MOA groups and far better when I am doing my job right. I tried to seat these at mag fit but the accuracy was inconsistent.

    Note: groups are only validated out to 400yds as that is as far as I have been able to shoot paper.
    Hunting is not a hobby.....its an addiction

  6. #6
    Member
    Join Date
    Feb 2013
    Location
    Vic Australia
    Posts
    33
    Ok thanks for that guys. Ill let ya know how I go thus arvo.
    Kjames what coal you running??

  7. #7
    Caretaker
    Join Date
    Dec 2011
    Location
    Hawkes Bay
    Posts
    9,265
    Quote Originally Posted by Bryan View Post
    I run two loads in my T3 7mm RM. IIRC they are:

    0-250yds: 160 Nosler Accobond, Norma brass, Fed 215GM primers, AR2217 (Can't remember amount), seating to fit mag, MV: 2800fps. Shoots honest 3/4 - 1.0 MOA groups.

    250yds+: 162 Hornady Amax, Norma brass, Fed 215GM primers, 75.5gr AR2225 (Compressed), 0.020" jump (single feed), MV: 3050fps. Shoots 1/2 MOA groups and far better when I am doing my job right. I tried to seat these at mag fit but the accuracy was inconsistent.

    Note: groups are only validated out to 400yds as that is as far as I have been able to shoot paper.
    Have you had many deer run off after absorbing the 160g Accubond? Or very delayed kills ?

    I refuse to use the 160AB now but am very happy with the 140AB or 162g Amax at any distance.
    DAF likes this.
    A big fast bullet beats a little fast bullet every time

  8. #8
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    5,058
    Quote Originally Posted by 7mmsaum View Post
    Have you had many deer run off after absorbing the 160g Accubond? Or very delayed kills ?

    I refuse to use the 160AB now but am very happy with the 140AB or 162g Amax at any distance.
    I've shot a couple of deer with 160AB from a 7mm mag. From memory about three red hinds a red spiker. All dropped on the spot.

  9. #9
    Lovin Facebook for hunters kiwijames's Avatar
    Join Date
    Feb 2012
    Location
    Hawkes Bay
    Posts
    7,205
    Quote Originally Posted by HartHunter2 View Post
    Ok thanks for that guys. Ill let ya know how I go thus arvo.
    Kjames what coal you running??
    3.7130" with a Hornady comparator (ogivish to base).

  10. #10
    Caretaker
    Join Date
    Dec 2011
    Location
    Hawkes Bay
    Posts
    9,265
    Quote Originally Posted by stug View Post
    I've shot a couple of deer with 160AB from a 7mm mag. From memory about three red hinds a red spiker. All dropped on the spot.

    Thanks Stug
    A big fast bullet beats a little fast bullet every time

  11. #11
    Member Bryan's Avatar
    Join Date
    Dec 2011
    Location
    Tauranga
    Posts
    873
    Quote Originally Posted by 7mmsaum View Post
    Have you had many deer run off after absorbing the 160g Accubond? Or very delayed kills ?

    I refuse to use the 160AB now but am very happy with the 140AB or 162g Amax at any distance.
    @7mmsaum I have had the opposite results.

    So far with this rifle I have shot 4 deer with the 160g Accubonds and all have dropped on the spot. All shot in through the shoulder at <250yds. I have had delayed kills on the 3 deer I have shot using the 162g Amax's (ranges from 290-420yds).

    I have used the 130gr Accubond in my .270win exclusively for the past 5 years and every animal shot has dropped instantly (ranges 20-320yds). This includes Reds (hinds, spikers, stags), Fallow, Goats.
    Hunting is not a hobby.....its an addiction

  12. #12
    Caretaker
    Join Date
    Dec 2011
    Location
    Hawkes Bay
    Posts
    9,265
    Thanks Bryan,

    I lost confidence in them years ago while i was hunting reds
    A big fast bullet beats a little fast bullet every time

  13. #13
    Member Danny's Avatar
    Join Date
    Aug 2013
    Location
    Central NI
    Posts
    5,087
    Interesting. So was that at range so reduced speed ?
    Pencilled through?
    What about the 150 LRAB anyone using this projectile in the 7RM?
    Dan M

  14. #14
    Member
    Join Date
    Apr 2014
    Location
    South taranaki
    Posts
    429
    I'm using 162gr Amax, federal 210 primers, 2213sc powder and pup brass.....2950fps and in my Remington shoots depending on me, between 1/2 and 3/4 inch at 100 meters. .

  15. #15
    Member
    Join Date
    Jul 2014
    Posts
    19
    Name:  7mm Rem Mag load.jpg
Views: 1089
Size:  94.2 KB
    My sweet spot load for the 7mm A-max
    7mmsaum and Gibo like this.

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!