I have read online that ya can make 7x57 cases from 270 brass fire forming with 16gn unique bit of Dacron and a wax plug,trim before fire forming any else done this I know it can be done from 3006 but that's not ideal cheers
Printable View
I have read online that ya can make 7x57 cases from 270 brass fire forming with 16gn unique bit of Dacron and a wax plug,trim before fire forming any else done this I know it can be done from 3006 but that's not ideal cheers
not yet......do you need some donor .270 cases to try it??
I did some 257 Robts case from .270 cases years ago, found I had to neck ream them as there was quite a bit of thickening at the base of the neck where the .270 shoulder was swaged into the .257 neck. It would be slightly less with a 7mm but would still be there & could cause problems if you've got a tightish chamber. Start you loads low in case.
@Micky Duck may do down the track i thinks theres a few in my swap meet box cheers
Depends on your chamber but have made plenty of 6.5x55 cases and 8x57 cases out of 30/06 cases and in military rifles they never needed neck turning. 8x57 cases were resized and cut off with RCBS trim die and loaded with no other prep. I have heaps of 260s and also 243s made from 308 cases and they work well.Quote:
Originally Posted by bluecod1967
I’d just run 8x57, 6mm rem or .257 Rob. Brass through a FL die if I couldn’t get new brass.
Sent from my iPhone using Tapatalk
those are probably harder to get than 7x57 lolQuote:
Originally Posted by Dicko
Fair bit of 8x57 around
Why not just buy new Norma 7x57 brass?
It's very expensive. Some of us are cheap. I have a bunch of old .270 around here. Im going to try it. .270 is basically a 7mm already.Quote:
Originally Posted by Double Shot
I have made it from 8x57 (no problem, just size it and done) I was also making 7mm Mauser from .30-06, because I have a lot of that lying around as well. This is trickier, because then you have to trim it really a lot, so I got a little pipe cutter and would cut the excess of before trimming it to proper length.
The trouble with .30/06, is that once turned into 7x57, it would get vertical splits in the neck after the second firing, so you had to anneal it, then you would get two more firings and then it was toast.
Maybe this wouldn't happen if I used .270 brass.
norma 7x57 brass from reloaders is $395 per 100 so that isnt going to happen i am only interested as i havnt attempted anything like that so i thought i would have a go cheers all
Sheesh!Quote:
Originally Posted by bluecod1967
Yes you can make 7x57 from .270, fireforming loads not necessary if you don't want to.
I've formed 6mm Rem, 7x57, 8x60, 7x60 from from .30-06 & .270 (and .35 Whelen just to see if I could)
Sometimes you can form in one pass without intermediate steps if you're careful, and have just the right amount of sizing wax.
I use privi brass in my 7x57R, it’s $1/case and pretty damm good if you can find some less the R.
Sell the .270 brass and it’s even less outlay.
Sent from my iPhone using Tapatalk
$395, yeh, bloody dear.
I would buy or swap 8x57 brass and one pass through the FLS die. Sell or swap your 270 brass.
Australia is a completely different market to NZ, even though it is just across the ditch. NZ is called a monopoly. You would be very lucky to see any 7x57R brass in NZ. There was some Norma a few years ago at about $3/case. The Euro brass importers to NZ are not interested in anything like 7x57R or 5.6x50R, etc.(even though some, like S&B, advertise it).