Thread: Lube Cases?

Hi guys,

Im newish to reloading , I was watching youtube today and this guy sprayed silcone spray on the cases instead of using the lube tray and lube. Is this addvisable and safe?

As it seems a good way to speed up the process.

Many Thanks.

Best case lube is redding sizing wax, and a little goes a long way

The convenient spray on lubes will give you a stuck case sooner or later and at the very least due to lower lubricating capabilities add extra effort required to the sizing processes.

Redding sizing wax on a cotton bud is a very efficient way to lube the inside of case necks, putting the product exactly where you want it and no where else

The redding product is also a perfect addition to the external surfaces on brass shoulders when fire forming, it gives much sharper formed shoulders and cases extremely close to fully formed internal capacity.

Steer clear of water soluble formulations as again they lack lubricity compared to the redding product and all of your fingerprints/product left on your dies and reloading equipment will cause surface rust.

Thanks 7mmsaum for the great advice.

I too am loading my first rifle ....done millions of pistol loads , straight walled , no shoulders , carbide dies etc etc .... lubing every single stinking case , and sizing and removing crimps and champfering ... for rifle , yee gods , what a pain I just want to pull the press and have lots and lots of completed bullets ....kinda is fun though, but when you have 2000+ 223 cases , it gets a little tedious

Originally Posted by stumpy

I too am loading my first rifle ....done millions of pistol loads , straight walled , no shoulders , carbide dies etc etc .... lubing every single stinking case , and sizing and removing crimps and champfering ... for rifle , yee gods , what a pain I just want to pull the press and have lots and lots of completed bullets ....kinda is fun though, but when you have 2000+ 223 cases , it gets a little tedious

Bro how do u have time with the wee sprogletts now ? By the way can you speed up the NZFS server its Fing slow and im over it......

I use neatsfoot oil and a stamp pad for the outside of my pistol and rifle cases. A little goes a long way.

I have been using lanolin for years.A little goes a very long way. Can be diluted with white spirits or alcohol.

Originally Posted by Driverman

I have been using lanolin for years.A little goes a very long way. Can be diluted with white spirits or alcohol.

I 2nd this, diluted with ethyl alcohol, good luck finding some, lay all my brass in a plastic bin lid and spray just the necks. Never have any trouble

Neck sizing - Hornady One Shot spray (the aerosol one), Angle spray so that the inside of neck is also lubed. I use a wooden loading block that only has the necks showing. One Shot just loves plastic trays ha ha.
FLSing - Stamp Pad and any of the good liquid lube oils. I use Lyman. Small wipe with same oil on cotton bud inside necks.
Case Forming - There is only 1 lube and I use Imperial Sizing Wax.
Hornady One Shot needs minimal clean up. DON'T BE TEMPTED TO USE IT FOR FLSING.
I keep clear of any water based lubes - snake oil - apart from potential corrosion issues they just don't posses the lubrication qualities of the likes of Imperial.

Originally Posted by zimmer

Neck sizing - Hornady One Shot spray (the aerosol one), Angle spray so that the inside of neck is also lubed. I use a wooden loading block that only has the necks showing. One Shot just loves plastic trays ha ha.
FLSing - Stamp Pad and any of the good liquid lube oils. I use Lyman. Small wipe with same oil on cotton bud inside necks.
Case Forming - There is only 1 lube and I use Imperial Sizing Wax.
Hornady One Shot needs minimal clean up. DON'T BE TEMPTED TO USE IT FOR FLSING.
I keep clear of any water based lubes - snake oil - apart from potential corrosion issues they just don't posses the lubrication qualities of the likes of Imperial.

I have used my first can of one shot and justed cracked the second last night.
I came up with a cunning plan of spraying the neck up in the block from 4 directions but then to get the lube to the bottom where its needed i put another tray on top and flipped it over so they were upside down and sprayed their bums!
Worked a treat and the brass was really smooth through the press so just a bit of lateral thinking has done the trick.
I rate the stuff personally and wilk be putting my third can into stock soon!

I use the spray can version of "one shot" Put them In a plastic container (plastic coleslaw or margarine) standing up and then just spray over the whole lot on an angle
I then size and later run them through a media tumbler.
NEVER EVER use the "pump spray one shot"
It's completely different product than the spray can version and will result in stuck cases
I've full length sized many thousands of cases this way using the spray cans with never having had a stuck case

I normally give a good spray then let stand for a couple of minutes and then give another light spray just before I size

I couldn't be bothered with the old fashioned way of lubeing

Forgot to add that if your neck sizing the full up a pill bottle with powdered graphite available from any hardware store, and dip the necks in, tap off the extra graphite and then neck size as normal

A bit dirty but works a treat

Anyone tested 'CRC Dry Glide with PTFE' for resizing ? It would be an interesting option if it works well.

Have also used for neck sizing Imperial Dry Neck Lube or just plain graphite powder and they are both effective. They tend to be a bit grubby though and like handling moly you end up with black marks on your white shirt, the light switches, the basin in the bathroom........

dillon case lube, spray on. Brilliant when you use it but not so good if you forget, eh