7mm PRC Springfield, just outta the box
She's seems all over the place, set up mint with a NF scope Attachment 246251
Printable View
7mm PRC Springfield, just outta the box
She's seems all over the place, set up mint with a NF scope Attachment 246251
Is it properly fitted to the stock?
Sent from my iPhone using Tapatalk
Twelve gauge n buck shot is it lol
Which dot were you aiming at ?
It’s the dope on the slope or the angle on the dangle. Then again it could possibly be the pitch in the ditch or the nut behind the butt.
Didn't he say a week or so back the new 7mm were shite??? Now it's getting revenge lol
My 7mm prc shoot like that if I clean it hard then takes a good 20ish round to group again
It'll be "within spec" or an "ammo problem" if he takes it back..
To many stickers.
Tooooo much Waikato.:beer:
Is that at 10m
Nothing to joke about.
Do the obvious,
Check scope mounts and screws.
Check stock screws.
Stock screws touching barrel?
Swap scope.
Different ammo
Like as said above
Are the rounds factory loads or reloads. I've seen poor reloading produce results like that. If they're not your reloads then use some factory ammo for a start
If its not the ammo then somethings loose or touching.
Was not aware that Springfield were doing a 7mm PRC...Quote:
Originally Posted by Philipo
Teach you for not buying a tikka!
Yep Phil I would be pretty slutted with that!
Won't be the scope
Sent from my SM-A226B using Tapatalk
My factory ammo was abit like that, until I started reloading with ADG brass
Sent from my CPH2145 using Tapatalk
Got to love that factory ammo
Bugger that alright
If it’s 300m it’s not too bad
Shoulda got a Howa
Looks like he's showing us the wrong side of the target as the holes break out this way. Either that or it shoots backwardsQuote:
Originally Posted by Philipo
Something is loose, shooter , action, bedding
Has barrel been broken in proper
Did you take the structural stickers off the stock? If so, looks like it's upset the whole feng shui of the rig.
But yeah. Ususal suspects, screws torqued correctly for action, rings, scope. Then ammo type and maybe bedding or a dodgy pressure point.
You don't shoot anything Phil so what does it matter?
Its a Model 2020?
Factory grease in the bedding ?
6.5 mm ammo ?
Actually shooting st 500m not 100 ?
No one has mentioned the shit 'scope.
Coriolis by the looks of it
Hitting suppressor?
Quote:
Originally Posted by Rushy
That depends on the heat of the meat
To quote I think Rick from the Young Ones show to Neil, "it's because it hates you".
Or was it Vivien to Rick?
Sounds more like Vivian.Quote:
Originally Posted by csmiffy
Stop it!Quote:
Originally Posted by Tahr
Sent from my SM-A226B using Tapatalk
The big hold up with the Springfield was the accuracy issues so I’d have thought that was pretty ironed out
Phillipo is no slouch on the range
But he is a joker
Perhaps he close his eyes and count to ten before letting rip
Wel well well, some good advice n opinions but sorry there's is no such thing as a 7mm PRC Springfeild yet ( they were meant to be in the country last year but still haven't be manufactured ) & no one mentioned the stickers, Yes careful observation would see that the top - right is actually on top of the bullet holes
We were having a sight in session ( new scope, new brake etc ) & one of the party brought a formica board with fully random placed stickers attached, problem was that the stickers did not stick & got blowin off when shot, made things tricky but I got two 7mil Mags & a 22-250ai sighted in & sorted
Was good for a laugh
Haha you are a twisted little man old mate[emoji23][emoji23][emoji23]
Sent from my iPhone using Tapatalk
Just read through this, what a nob!
I'd swap out your ammo for something really different (say you had Hornady VLD's boat tails there in your test, try a flat base hunting bullet).
-Did you dial out the parallax error on your scope?
