Thread: Brno Model 1 1950

@Apocalypticaman & @Lucky as l thought l only kept the article on the Pre 1950 Model 1 & 5's that l like ,but if you go through the links it has fix for the later models ,l will link a couple of them & then the multi link to all things Brno on RC. Hope it helps

Adjusting the Non-Adjustable Brno Model 1 Trigger

https://www.rimfirecentral.com/forum...d.php?t=419463

Brno Model 1- easy trigger tune.

https://www.rimfirecentral.com/forum...d.php?t=394265

Brno Model 1 and 3 with Poor Man’s Trigger Job

https://www.rimfirecentral.com/forum...d.php?t=389669


Trigger Pictures: Brno #1/3 vs CZ 452's and Brno Model #2/4/5's

https://www.rimfirecentral.com/forum...d.php?t=161209

My last Brno post, EVER !!! ....

https://www.rimfirecentral.com/forum...d.php?t=184522



The CZ & BRNO Info Thread
https://www.rimfirecentral.com/forum...d.php?t=333700

Originally Posted by zimmer

Have you used them? They don't appear to ship out of Australia?

Yes. I had the front sight hood sent to my son's NSW address and then he sent it to NZ.

I wasn't in a hurry...

Originally Posted by Pauli

Yes. I had the front sight hood sent to my son's NSW address and then he sent it to NZ.

I wasn't in a hurry...

Great idea …..

My BRNO No 2 story.

After a lot of searching over a couple of years my No 1 eventually came sadly from a friend's estate.
I'm sure he would have been happy though for me to have it.

Mine's condition overall was very good, better than anything Tardme peddlers were trying to sell for a grand and up. That bubble seems to have burst now.

Two problems with mine -

1/ The butt plate has shrunk and lifted slightly between the two screws. This is a common issue. Replacements for these are very rare worldwide. There was a Yank making very good replacements but he doesn't reply to emails. Model 2s etc no problem. I'm still looking.

2/ The other problem was the 2 stage trigger. If the first stage was taken up and the shot not taken the trigger would not return to the starting point. This can sometimes be caused by attempts to lighten the trigger spring too much. In my case I could see a very very small depression on the sear surface. I carefully polished it out but the trigger still wasn't 100%.

I then found a guy called jojo_svk selling BRNO parts on Ebay. (He was also active on Rimfirecental at the time.) He is in Slovakia. I thought yeah right. Then desperation set in I thought let's try him. Well, he had an unbelievable range of spares virtually all new. IIRC the only used parts were bolt bodies.
Although I didn't need most of them but because they were available, I ordered a firing pin, a mainspring, a cocking piece, a trigger, bottom metal and 2 butt plate screws and of course a fore-sight protector.

The order arrived pretty quickly (why does it sometimes take forever for stuff from USA) and the shipping cost was very reasonable.
The 2 screws however were missing (something like 2-3 dollars US) from the order. I was going to let it go as I'd only ordered the screws in case I had difficulty removing the old ones should I ever get a replacement butt plate. I reconsidered and politely informed jojo-svk. He replied overnight, was very apologetic, and said that he’d already sent off the screws, shipping at his cost. The package duly arrived and to my surprise he’d sent 2 sets of all the rifle’s screws not just those for the butt plate.

I asked him about replacement butt plates for the No 1. He said he couldn’t help but received many enquiries for them.

My trigger is now superb. Original problem solved.
I also now have spare parts should I pick up another No 1.

Overall a great experience with jojo-svk.

Originally Posted by zimmer

My BRNO No 2 story.

Shit, No1 not No 2 although I'm keeping my eye out for a pre 67-68 No 2.

Originally Posted by zimmer

......The butt plate has shrunk and lifted slightly between the two screws. This is a common issue. Replacements for these are very rare worldwide. There was a Yank making very good replacements but he doesn't reply to emails. Model 2s etc no problem. I'm still looking. ..........

I had the same issue with a Model 1 and 1957 Model 2. What I think happened (in my particular case) was the butt wood had swelled rather than the butt plate shrinking. The butt plates appear to be made of some type of very hard plastic.

Originally Posted by zimmer

My BRNO No 2 story.

After a lot of searching over a couple of years my No 1 eventually came sadly from a friend's estate.
I'm sure he would have been happy though for me to have it.

Mine's condition overall was very good, better than anything Tardme peddlers were trying to sell for a grand and up. That bubble seems to have burst now.

Two problems with mine -

1/ The butt plate has shrunk and lifted slightly between the two screws. This is a common issue. Replacements for these are very rare worldwide. There was a Yank making very good replacements but he doesn't reply to emails. Model 2s etc no problem. I'm still looking.

2/ The other problem was the 2 stage trigger. If the first stage was taken up and the shot not taken the trigger would not return to the starting point. This can sometimes be caused by attempts to lighten the trigger spring too much. In my case I could see a very very small depression on the sear surface. I carefully polished it out but the trigger still wasn't 100%.

I then found a guy called jojo_svk selling BRNO parts on Ebay. (He was also active on Rimfirecental at the time.) He is in Slovakia. I thought yeah right. Then desperation set in I thought let's try him. Well, he had an unbelievable range of spares virtually all new. IIRC the only used parts were bolt bodies.
Although I didn't need most of them but because they were available, I ordered a firing pin, a mainspring, a cocking piece, a trigger, bottom metal and 2 butt plate screws and of course a fore-sight protector.

The order arrived pretty quickly (why does it sometimes take forever for stuff from USA) and the shipping cost was very reasonable.
The 2 screws however were missing (something like 2-3 dollars US) from the order. I was going to let it go as I'd only ordered the screws in case I had difficulty removing the old ones should I ever get a replacement butt plate. I reconsidered and politely informed jojo-svk. He replied overnight, was very apologetic, and said that he’d already sent off the screws, shipping at his cost. The package duly arrived and to my surprise he’d sent 2 sets of all the rifle’s screws not just those for the butt plate.

I asked him about replacement butt plates for the No 1. He said he couldn’t help but received many enquiries for them.

My trigger is now superb. Original problem solved.
I also now have spare parts should I pick up another No 1.

Overall a great experience with jojo-svk.

I have the same issue with the butt plate. My thinking was, if it ever got cracked or damaged I’d get a metal but plate made specifically for it by a good gunsmith.

It would certainly be worth doing IMO

You can all go sit in the naughty corner. Two pages in on a hunting forum and no one mentions the Ploughed paddock in the back ground!.

I know they are nice rifles but come on people those hogs are just taking the piss.


PS I did see the house as well.

I am not sure that Model 1 butt plates shrinking is correct - my understanding is that the butt plates were always small relative to the stock size. From a BRNO collector's perspective, having a Model 1 butt plate the same size as the stock is the first sign the stock has been sanded down/fiddled with. Regardless; if you have a Model 1 with a small butt plate, you should be happy with it!

Originally Posted by huntsika

I am not sure that Model 1 butt plates shrinking is correct - my understanding is that the butt plates were always small relative to the stock size. From a BRNO collector's perspective, having a Model 1 butt plate the same size as the stock is the first sign the stock has been sanded down/fiddled with. Regardless; if you have a Model 1 with a small butt plate, you should be happy with it!

I agree with @huntsika

Quote Originally Posted by Pauli View Post
https://www.rebelgunworks.com.au/col...ont-sight-hood

Had the same issue recently. If you have friends / family in Oz get them to send it to them and forward it onto you here. That's what I did, no issues.

Might be a stupid question but I have a steel front sight cover for a CZ 527 .222 at home if it fits or is suitable.

Got a sling you can have free

Originally Posted by bunji

@Lucky These early Brno's have a easy trigger to work on ,from memory up to 1950 they had the "non Adjustable "... l have a good instruction article saved somewhere & l will dig it up for you .

Try this;
https://www.rimfirecentral.com/forum...d.php?t=419463

Might even try it on mine

After looking for a Brno model 2 that was in good nick, by chance i was able to get this 1952 model 1. Yet to take it out to the range but if it shoots well I am keen to replace the existing scope.

To the experts out there, can you recommend a suitable variable scope suitable with decent eye relief that will fit existing rings and not require removal of rear sights...if thats possible.

Thanks in advance
m