Euro Arms of America .45 black power info needed

Hey brains trust
I'll start by saying I am a complete novice to black powder and this was an impulse buy
I spent an hr googling with limited results info on my newly purchased Euro Arms Of America .45 muzzle loader.
all I could find was the AB markings mean it was built in 1976
My question is what projectile should I use? it appears to have some grooves in the barrel but they almost look straight
I think I'll try find a club or knowledgeable persons around Whangarei to help me set it up and get shooting but if i could have a few bits and pieces ready would be good
any info much appreciated cheersAttachment 226280Attachment 226281Attachment 226282

You probably put about 60 grains of FFFG down the barrel, after cleaning any oil out and depending of the twist, stuff a round ball with a greased patch or a greased 45 cal projectile down the barrel, put a cap on the nipple, point it in a safe direction and pull the trigger.
Now two things you need to know, there are to be NO air gaps between the powder and the projectile, it must be rammed tight onto the powder, measure on the rod to know when its home.
Secondly, you cannot over load with power, if you put too much powder in, it will be wasted, un burnt out the barrel, so that’s a good thing and only use black powder.
You can use grades FFFG or FFG, 45 I’d use FFFG
Be careful with hang fires, they can be very dangerous, if it doesn’t fire, don’t go looking down the barrel. You can try another cap, but leave a good few minutes if it doesn’t fire second time, you can then remove the nipple, clean, dry, put in new powder under the nipple, refit nipple and try again.
I may have a book here I can send to you. I’ll have a gander tomorrow, i may also have some round ball
Enjoy

And before you load it and after you've cleaned the bore fire a couple of caps to clean the fire channel out

Always fire a cap before loading after storage


So you will also need a nipple key for its removal.
Don't take the nipple out every time you clean it or the threads will wear prematurely

As maca 49 says it's rifled probably 1:40 or slower so start with round ball. The old fashioned way with those to get the charge is to place the ball in the palm of your hand and pour powder onto it till it reaches the top. Like maca I've got some instructions somewhere which I'll dig out. You'll also probably want a short starter, nipple wrench and a worm for removing balls that were loaded without powder.
Welcome to the dark side🙂

cheers for that, any advice on where to buy the gear? doing a google and I keep finding parts here and parts there

Reloaders or a good local owner run sports goods shop that understands hunting for a mold, same for percussion caps, it looks like that will take no 11 caps cci amongst others make them. Lube make yourself beeswax and tallow or lard 1: 3 or straight lard, beeswax is too hard on its own. If you load and fire pretty much instantly a "spit patch" ( wet ) is hard to beat. Still looking for that book.

Quote:

---

Originally Posted by Marty Henry

Reloaders or a good local owner run sports goods shop that understands hunting for a mold, same for percussion caps, it looks like that will take no 11 caps cci amongst others make them. Lube make yourself beeswax and tallow or lard 1: 3 or straight lard, beeswax is too hard on its own. If you load and fire pretty much instantly a "spit patch" ( wet ) is hard to beat. Still looking for that book.

---

Well he's crap out of luck being in Whangarei for a sports shop with any Black powder support.
However there are a fair few BP shooters up here. (I'm not one)

Hi I am literally a couple of k away from you (Kauri), give me a call we can talk about the gun and I have local contacts to get all that you need.

Cheers
Darren 021 2238222

Found it. Lyman 43rd edition 1964. Some are probably upside down or sideways and they may not be in sequence but I'm sure you can sort that out, as I can't.
Seems page 1 is in the middle page 2 is above it upside down and page 3 is last splendid effort.!

Old timer's saying..."ram the powder, not the lead...if you want to kill them dead".

Looking at your pictures it looks like you have a Investarms Hawken. There should be an (I) or similar imprinted on the barrel. The barrel will be 1-48 twist rate and for use with Round ball or conical bullets (I shoot round ball). I would try the following 60 grains of powder FF or FFF, a .440 round ball and a Ticking patch (buy ticking from a draper) I just cut strips into squares a bit larger than the barrel is across. Lube the patches with olive oil, moist not wet.
Ther are some good videos on YouTube . Search how to load a muzzleloader.

Google / PR0502 Dixie Hawken Rifle / This is what you have only these days the lock is stamped with engraving.