Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Ammo Direct


User Tag List

+ Reply to Thread
Results 1 to 9 of 9
Like Tree7Likes
  • 2 Post By Seventenths
  • 1 Post By 25 /08 IMP
  • 2 Post By Scout
  • 1 Post By BSA270
  • 1 Post By Scout

Thread: Shortening into fluted barrel

  1. #1
    Member stagstalker's Avatar
    Join Date
    Jul 2018
    Location
    North Island, New Zealand
    Posts
    2,190

    Shortening into fluted barrel

    I’m pretty sure I have read that it’s allgood depending on how deep the flutes are but is it generally ok to shorten and thread a fluted Tikka barrel back in the flutes or can it have issues? I compromised on my Tikka rem mag and shortened back to just shy of the flutes.

  2. #2
    Member
    Join Date
    Dec 2011
    Location
    Clutha
    Posts
    1,418
    I shortened my tikka fluted barrel to 16 inches which was a 7mm-08 reamed out to .284

    It was shortened by Gunworks well into the flutes and I never had a problem.
    25 /08 IMP and stagstalker like this.

  3. #3
    Member
    Join Date
    Nov 2012
    Posts
    1,527
    Quote Originally Posted by stagstalker View Post
    I’m pretty sure I have read that it’s allgood depending on how deep the flutes are but is it generally ok to shorten and thread a fluted Tikka barrel back in the flutes or can it have issues? I compromised on my Tikka rem mag and shortened back to just shy of the flutes.
    Yip it's all good seen plenty done at 18" and we'll down into the flutes.

    Sent from my CPH1903 using Tapatalk
    stagstalker likes this.

  4. #4
    Member
    Join Date
    Feb 2018
    Location
    Waikato
    Posts
    1,308
    It does depend on what size you want to thread down to, I did my Sako Finnlite & I wanted 14/1 & really that is not quite enough, I haven't used it enough yet to say but I think it will be ok, a couple of the Flutes were slightly deeper than others so not fully threaded .

  5. #5
    Member
    Join Date
    Feb 2018
    Location
    Waikato
    Posts
    1,308
    Name:  IMG_4440.jpg
Views: 782
Size:  204.5 KBName:  IMG_4441.jpg
Views: 758
Size:  195.6 KBName:  IMG_4442.jpg
Views: 991
Size:  218.2 KBName:  IMG_4443.jpg
Views: 794
Size:  234.8 KBName:  IMG_4444.jpg
Views: 796
Size:  235.0 KB

    This is cut to 16in, I would have gone to 14in but suppressor would be into forend .
    takbok and stagstalker like this.

  6. #6
    Member
    Join Date
    May 2012
    Location
    Far North
    Posts
    4,881
    Wonder if it's threaded off the bore rather than the outside and the hole doesn't quite go down the middle

  7. #7
    Member
    Join Date
    Mar 2017
    Location
    Palmerston North
    Posts
    189
    Had my tikka T3x superlite .308 shortened to 16" by DPT and one of their suppressors fitted. They wouldn't do it if any problems doing so. Hasn't effeced the accuracy at all.
    stagstalker likes this.

  8. #8
    Member
    Join Date
    Feb 2018
    Location
    Waikato
    Posts
    1,308
    Quote Originally Posted by Bill999 View Post
    Wonder if it's threaded off the bore rather than the outside and the hole doesn't quite go down the middle
    Very likely as it seems most of the "holes" aren't plum dead center of barrel, but on this barrel you can see some of the flutes are deeper & wider, need to check more of them to tell for sure .
    Bill999 likes this.

  9. #9
    Member Ftx325's Avatar
    Join Date
    Jul 2020
    Location
    Nelson
    Posts
    3,128
    Quote Originally Posted by Scout View Post
    Very likely as it seems most of the "holes" aren't plum dead center of barrel, but on this barrel you can see some of the flutes are deeper & wider, need to check more of them to tell for sure .
    It certainly sounds like the hole is off center as I would imagine the barrel would be positioned in machinery using the hole as centre for the flute cutting which would explain the deeper flutes on one side. Probably would be held same way for threads I would think so they would be centered on hole rather than barrel external.
    born to hunt - forced to work

 

 

Similar Threads

  1. Will Shortening my barrel cause issues?
    By KaneB in forum Firearms, Optics and Accessories
    Replies: 15
    Last Post: 29-09-2018, 05:21 PM
  2. Ak barrel shortening
    By Kurt557 in forum Projects and Home Builds
    Replies: 3
    Last Post: 20-05-2018, 03:53 PM
  3. Shortening CZ 452 barrel - FAO: DPT
    By MB in forum DPT Machinists
    Replies: 5
    Last Post: 04-07-2017, 01:14 PM
  4. Barrel shortening
    By Tertle in forum Shotgunning
    Replies: 2
    Last Post: 07-12-2016, 08:02 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!