Just brought a new tikka 6.5x55 about to send it away to get suppressed . Going to send it up north to HARDY engineering.
Any idea before I send which model suppressor to choose and length to trim of barrel or left factory length?
Printable View
Just brought a new tikka 6.5x55 about to send it away to get suppressed . Going to send it up north to HARDY engineering.
Any idea before I send which model suppressor to choose and length to trim of barrel or left factory length?
I have a DPT over barrel, cut my swede to 20" and don't miss much speed - I get 2740 fps from 143gr ELD-X
I'm shooting 120 gr noslers bench mark 2 what kind of load are you using for the bigger 143gr
You have one of the best gunsmith in the country in Wakefield. Why send it away?
There is only two suppressors I will never buy again, Hardy and Rev Rog......(SubSilentSupprssors) If you get a good Hardys then its fine, but if anything ever goes wrong their service leaves a LOT to be desired. DPT and Gunworks both do a decent suppressor with great service and I will use either again when I am noext on the market for a suppressor. Likewise Maniatis (Not sure of his brand name) also makes them here in chch.
Send it to dpt or gunworks both give great service forget hardy
Depends what you're after... obviously the DPT is very popular on this forum. Darren does excellent work and stands by his product.
There are others that offer excellent service like Scotty at SSRNZ, the Tiffens @ Gunworks, Stuart at Greystone Guns and the crew at MAE.
DPT would be the lightest if you're going to carry it.
Whats the intended use? I've just gone with Stuart for a Varmint rig so don't mind the weight.
There's been big changes at hardy's as I have heard of 4 separate people that have as the old saying goes "we will put it right"Quote:
Originally Posted by timattalon
Happen for them.
Their stealth on a 6.5 55 is out standing as i now have heard three and shot a couple as well.
Great recoil reduction as well.
There is a reason that they topped the rod and rifle test and that's because they do work.
My two cents any way!
Sent from my SM-G950F using Tapatalk
I've been as low as 18.5 on my tikka 6.5x55 there is a good thread on here that I started. Give the search button a whirl.
46.2gr 2209Quote:
Originally Posted by Sr5dan
[QUOTE=chalkeye;669357]46.2gr 2209[/Quote
Cheers ill give it a crack
Wakefield sorry for my ignorance who is that
Sorry for my ignorance who is the gun Smith in wakefieldQuote:
Originally Posted by nor-west
You on commission Andy ?Quote:
Originally Posted by andyanimal31
How did you know!Quote:
Originally Posted by Kiwi Greg
Sent from my SM-G950F using Tapatalk
Dave Ward just Google his name with gunsmith it will come up.
For the most part, the suppressors are good. But it was not an employee that provided the service I experienced, but the boss so unless they have replaced him.....Quote:
Originally Posted by andyanimal31
I was not going to go into detail, but I had a Hardy's suppressor that when used, would leave a coating of soot on the outside of the barrel. I contacted him to see what could be done to stop this and because the suppressor / rifle was second hand I explained I did not expect it to be covered by warranty. His reply was "our suppressors dont do that, it must be the rifle. Well I checked and there are no holes to cause that leak in my barrel!!!!!! He was not even prepared to deal with the idea it may by faulty. Service like that does not deserve a customer to return when there are many viable alternatives out there.
(Afterwards we found the swarf from threading had not been cleared from where the barrel sleeve is threaded to the internals at the muzzle end and was not sealed because of this so it was an error in manufacture)
I still maintain the every business will make a mistake at some point. It is how that company deals with the mistakes that sets them apart from others. And he set is apart from all the others that provide any sort of service or customer satisfaction.
Every time I think about going to Hardy, one of these threads pop up.
It's a bit of a shame really as his products clearly work well but I'm put off by the CS.
If they did these threads wouldn't pop up so often & his CS wouldn't be required as often.....Quote:
Originally Posted by SlimySquirrel
You will find most people are far too polite to post their experiences on this type of thread.
I am reluctant, but he has cost me so many dollars over "faulty" products that I am equally reluctant to not speak out, especially when I'm at fault not his perfect products.....
What makes it worse is I have a few clients in Aussie who have the same or worse experiences as myself & others I know of
Its the old adage, make one customer happy and they will tell their friends, piss one customer off and they will tell everybody.....
I went in to see a gunsmith about getting my rifle re threaded and up grading from my gunworks. He see's alot of suppressors and has seen things go wrong with ALL brands.
gunworks well made but heavy and long. old technology
dpt light but they do out quicker (will only sell with s/s baffle) also design want change.
hardys always looking for new products to improve his products.
I generally run MAE's but recently got an A-Tec and found it to be superb on my 6.5x.284, use it on the .243 and am now getting another for my .22-243.
Lightweight, excellent noise reduction and lesser recoil, certainly worth a look at, Try Stager Sport in Alexander...
Just admit it Andy, You want to have Dan's babies aye :DQuote:
Originally Posted by andyanimal31
Have you hacked into my communications there big boy!Quote:
Originally Posted by Philipo
You seem to have access to some very private information!
Sent from my SM-G950F using Tapatalk
Hardy on my 308 bushpig which goes real well. Mate who does alot of shooting swears by DPT and he runs one on his 6.5x55 with a 15" barrel Carl Gustav which shoots mint. Have an MAE on my 222 as per a recommendation from @Double Shot and he was certainly no wrong that they are great supps