Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Night Vision NZ


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 18
Like Tree4Likes

Thread: Tikka action screws

  1. #1
    Member SlimySquirrel's Avatar
    Join Date
    Aug 2012
    Location
    Sydney
    Posts
    1,306

    Tikka action screws

    Morning all,

    Just managed to strip out my rear action screw at 50 inch pounds when torquing into a B&C stock...

    What replacement screws do you recommend? I have read that 60-65 inch lbs is the go to for B&C so I would like to find some replacements that will hold that.

  2. #2
    Member 199p's Avatar
    Join Date
    Dec 2011
    Location
    Palmerston North
    Posts
    4,281
    I think its gunworks down south that do a stainless steel set
    SlimySquirrel likes this.

  3. #3
    Gone But Not Forgotten
    Join Date
    Feb 2014
    Location
    Taupo
    Posts
    1,887
    That's a lot of torque for a rear action screw. Are you sure it's the recommended?

  4. #4
    Member
    Join Date
    Jun 2013
    Location
    West Auckland
    Posts
    73
    I was under the impression it was around the 35lb mark, interested to see what others think.
    Shootm likes this.

  5. #5
    Member SlimySquirrel's Avatar
    Join Date
    Aug 2012
    Location
    Sydney
    Posts
    1,306
    Yep, I hear ya... I believe that 35lb is for the standard stock to stop it from distorting.

  6. #6
    Caretaker
    Join Date
    Dec 2011
    Location
    Hawkes Bay
    Posts
    9,265
    Standard stock is 40 inch pounds on the front and 35 rear

    B&C or HSPrecision is 65inch pounds front and 35 inch pounds rear
    SlimySquirrel likes this.
    A big fast bullet beats a little fast bullet every time

  7. #7
    Member SlimySquirrel's Avatar
    Join Date
    Aug 2012
    Location
    Sydney
    Posts
    1,306
    Cheers boss... now... How do I get that screw out....

  8. #8
    Member Kooza's Avatar
    Join Date
    Sep 2014
    Location
    Napier
    Posts
    636
    If your fussy, I changed my t3 screws to the stainless sako ones, not cheap tho.
    Went to buy some camouflage trousers the other day but I couldn't find any.

  9. #9
    Member SlimySquirrel's Avatar
    Join Date
    Aug 2012
    Location
    Sydney
    Posts
    1,306
    Not fussy mate... just dont like em threading out on my nasty ass Gorilla hands...

  10. #10
    Member gadgetman's Avatar
    Join Date
    Jan 2012
    Location
    Christchurch
    Posts
    17,981
    Is it a snapped screw or stripped thread?
    There are only three types of people in this world. Those that can count, and those that can't!

  11. #11
    Member SlimySquirrel's Avatar
    Join Date
    Aug 2012
    Location
    Sydney
    Posts
    1,306
    Stripped thread ...

  12. #12
    Member
    Join Date
    Mar 2013
    Location
    Bell Block NZ/Northern Alberta Canada
    Posts
    1,137
    Normally you apply separation force between the two parts, and turn the bolt/screw undone, or grind/cut the head off, and remove the two half's, and deal with the striped bolt after.
    Seen as you are now going to need, an thread insert installed, consider dropping it off at a gun smith or machinist.
    Now for sum free advise, buy sum antisieze, put it on every bolt and screw in steel, that does not spin round, at a great rate of knots, And yes I use it on my scope mounts and bases, shock and horror, you can use locktite, but the only thing worse than a striped thread is a striped alan bolt or torx head, grrrr.
    Also torque on hardware is very different, between dry and lubed, a tiny bit of lube, on thread and the contact face on the head of the bolt, (antisieze is fine) allow a much smother torque, and prevent galling and false torques readings.
    Know the difference between ft lbs, inch lbs and Newton meters, as well as thou and hundreds of a MM, there has been an awful pile of balls up's, over the years, getting them wrong. or assuming, the tools you used were one, when they were the other.
    10-Ring likes this.

  13. #13
    Member SlimySquirrel's Avatar
    Join Date
    Aug 2012
    Location
    Sydney
    Posts
    1,306
    Ha-ha... Yeah man. It's a fat wrench so it only goes to 65.

    Thanks for the heads up.

  14. #14
    Member Sasquatch's Avatar
    Join Date
    Nov 2014
    Location
    The Forest
    Posts
    3,035
    I have the B&C and have the front and rear action screws set at 45 inch pounds. 65 inch pounds seems a tad high for that rifle stock.

  15. #15
    Member
    Join Date
    May 2012
    Location
    North Otago
    Posts
    417
    Was it the screw or the action you stripped

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!