Printable View
Anybody on here refinished a wooden stock with a polyurethane finish?? Interested in products used and how the stock looked once finished??????..... Looking to re do a factory stock, undecided as to use oil/ or re apply a polyurethane finish. Stock will be lightly used working bush rifle.
I am a fan of Tru Oil. Minimal amounts, smoothed on with fingers. Sand with very fine wet and dry paper between coats after leaving 24 hrs. Build up 10 or more layers and final rub with 0000 wire wool or a worn green scotchbrite pad.
Yeah, done a couple of "quick" (purists would say rough) overhauls with polyurethane. Rubbed existing finish back a bit with 4 naught steel wool. Gave the stock a good rub down with methylated spirits and then applied 3 coats of spray on gloss polyurethane. Light rub down between coats with steel wool. Final results ended up too glossy so applied a final top coat of matt spray polyurethane. Came out quite OK. Appears to have been quite durable.
Normally though I do a full strip down using paint stripper and finish with around 10 light coats of Birchwood Casey Tru-Oil.
Yep done some with Tru Oil & if the wood is light coloured BC's walnut stain adds a good colour.
Sent from my GT-I9192 using Tapatalk
My old man is currently refinishing the classic Rem Model 7 i got for him a few months ago, the factory polyurethane finish was near mint, but theres only one way to have a wooden stock rifle apparently, and thats oiled. Dad is a good old school boy, and has done plenty of stock making and refinishing, modifying stocks for people etc, so he'll do a mint job, im looking forward to seeing it finished.
I got a wee wooden stock Toz for Christmas that had a disgusting plasticy finish on it.
I cut the stock down to fit my midget arms, then sanded with three grades of paper, finished with a scouring pad from the kitchen.
Bought a cool half/half stain/oil from Mitre10. I applied three coats and haven't put any sealant on it.
Just a regularly used bunny/plover hack but it's worn well so far [emoji5]
Sent from my iPhone using Tapatalk
ive used spray can poly on stocks its worked well for me
Yep another Tru Oil fan here. Takes longer but the results are far better. Just done a Parker Hale sporter .303. Came up mint.
Sent from my GT-I9300 using Tapatalk
Yeah, tru oil for me also.
Did a cz stock a few years back and it turned out super.
This actually reminds me, I have to re finish the Marlin 917 stock again before I get it ceracoated to stop the surface rusting.
I'm following this with interest. I've got brno stock on the way to redo. I've bought some dad's varnish remover to use. What I'm stuck on is the re oil part, I've used true oil on stocks to repair the barrel chanel after a free float
But I'm thinking maybe Danish oil is worth a look?
Water or oil based?
no polyurethane finish is good as its a surface finish, if it gets a crack water gets in not out. birchwood casey tru-oil is great and they also have a kit that includes, stain. oil and wax. along with the correct wire wool etc
tru oil and amour all 50 50 mix you can finish a stock in a day.
Yeah tru oil for me stock came up real nice, been looking at logcabinlooms on you tube and he swears buy pine tar and boiled linseed oil 50/50 mix and apparently its what the Fins used to use on there rifle stocks. His guns look nice with a dark sort of finish.
here is me using tru-oil...
http://www.nzhuntingandshooting.co.n...ock-how-18532/
That looks mint Gruntzer.
I will be using the last of the walnut stain I have so hoping it gets as dark as that. Will look nice with graphite black ceracoat.
Ive just spoken to Dad, and he uses a recipe of boiled linseed oil (about 2/3's) with 1/3 of turps added with a dash of terrapin?(not sure of spelling, but its a drying agent). It has to be boiled up before each time its applied, and it sounds like he does lots of coats, and it takes some time, but the finish is awesome, he said Tru-oil is a cheats short cut way ;-)Quote:
Originally Posted by GWH
Haha... so is driving instead of walking...
what about putting an oil finish on a laminate stock? is there risk of damage or de-lamination? i'd imagine the polyurethane would provide greater moisture protection.
Hey GWH,, could you ask your dad what he does to keep the chequering clean while hes doing the oil finish.
Plus question for those using bc tru/oil. When youve finished applying with say your final coat, is it in anyway tacky to the touch??? If it is whats the best way of getting rid of it, could you wipe it down with say methylated spirits or such like??
The only time I have had a "tacky" finish was on one stock where I tried Danish Oil. I don't think it was the fault of the Danish Oil though just I hadn't neutralised the paint remover correctly. Ended up stripping that one and starting again using Tru-Oil. Sometimes the first coat of Tru-Oil stays a bit tacky for longer than expected. I just leave the 1st coat for a few days make sure it has absolutely dried b4 adding the ongoing coats. After the 1st has fully dried each coat after is given a day to dry, depending upon the climate at the time. The later coats are dry to touch within hours. It is not a process to be rushed unfortunately. The other thing I have found with Tru-Oil is you get a far better result with a new bottle. No matter what you do old bottles tend to go thick and are no good for use. I tried thinning but although the shit was more fluid the result on the stock was irregular. And it is no good trying to tighten up the bottle real tight either to prevent evaporation – all that happens is you cannot get the stupid child proof cap to open again.Quote:
Originally Posted by matagouri
Tru-Oil versus Linseed. I find Tru-Oil gives a more durable finish with virtually no ongoing maintenance. I do apply Birchwood Casey Wax occasionally. Linseed gives a more traditional deep luster finish but requires extra coats over time to maintain the finish. Also when doing stocks I water proof the internals, barrel channel, trigger group inletting, behind the butt plate etc at the same time with polyurethane (or a marine varnish) applied by brush, no spray.
I tried using tru oil on my boyds laminated stock since all the polyurethane was chipping off, but the oil got rubbed off on parts and the wood delaminated slightly after a few days hunting in wet bush.
just the answer i needed before going headlong into a harebrained home DIY....
Quote:
Originally Posted by MDub
Use a tooth brush, preferably a hard one to clean out the oil. I used to use the linseed oil and turps mix to do stocks but have now changed to Scherell dark oil and this gives a very nice finish. Once it has the finish that I am happy with I leave the stock for a week or so and then use danish oil to waterproof the wood. I put the oil on by hand and leave it for for approximately a minute and then rub it off with a peice of old net curtaining. after 10 odd coats you end up with a warm glow type finish rather than a real shiny one.Quote:
Originally Posted by matagouri
Works for me and the punters seem to like it as well
With BLO, how does it handle shit conditions like wet bush ?
If there has not been enough BLO used then you can get what I call leeching i.e. the stock will go slightly pale due the the oil getting wet and rubbing off. I used to put the oil on after I had warmed it up as it soaks in more quickly but it does take a fair bit of work to get a good oil finish, its not an over night job.
@Chop3r Thank you, do you recommend me look at that Scherell dark oil you mentioned to do a Brno ZKK601 stock? I would assume its beech wood? will that give me a better/durable finish than the BLO.
Your Brno should be walnut and yes it will give a better finish in a far shorter time, go for the dark oil. There is a bloke on trademe that sells it, $21, look in the firearms accessories
Legend, Thanks.
I can't stand tru oil. Nothing beats BLO for finish but it is time consuming. I have a bucket of genuine tung oil here which is supposedly superior but I always go back to BLO for walnut. My fox was blo finished Tim and it was always getting rained on. I like the ability to easily touch up an oiled stock too. If you want to see examples of it have a look in my safe next time we cross paths, every wooden stocked rifle or shorty I own is oil finished, some of them approaching 140 years old