Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Terminator Ammo Direct


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 27
Like Tree12Likes

Thread: Any Diesel or tractor mechs on here?

  1. #1
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247

    Unhappy Any Diesel or tractor mechs on here?

    Yesterday on the way back from a job my tractor started to spew coolant from the reservoir and warming up, didn't overheat.
    Topped it up to make it back home. Let it cool down then topped up coolant to proper level. Took belt off water pump and turned the engine on with reservoir cap off, few second later coolant was blowing out.
    Am I right that it has a blown head gasket and combustion gas blows into cooling system?
    There is no oil present in coolant , there were bubbles in tank first time I opened it.
    No coolant in engine oil.

    If it's a HG could I remove rockers without the need of re-setting timing? I think I can do a HG job (did a few on SJ413s) the only thing that worries me is the timing.
    Water pump got replaced 15Hrs ago, cost me 2.5k so would be keen to fix myself. I would image this sort of work could go up to the 5-6K mark.
    Engine is JD 4045TR

    Any advice would be much appreciated.

    Thanks
    BF
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  2. #2
    Member
    Join Date
    May 2015
    Location
    Southland
    Posts
    1,061
    @boarFreak

    As @Mauser308 has mentioned or maybe one of the following, and in the order of cheap to expensive to replace

    1, head gasket
    2, cracked head
    3, cylinder liner damage

    You can by test kits that will indicate if its combustion gas in the coolant.
    I don't think they are an over head cam engine. If that is the case, removing the head should be a pretty simple operation and you wouldn't need to worry about any timing issues.
    You would need to remove the head to diagnose any of the 3 issues above!
    You will have to do your home work though as the bolts may be "torque to yield" so would need to be replaced.

    Check out You Tube to see if there is anything on there about head gasket replacement on these engines.

    If it was mine, I'd be giving it a go! I reckon an SJ413 would be more of a mission!

    Good Luck
    Last edited by Fireflite; 28-06-2020 at 05:02 PM.

  3. #3
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    Could even just be something as simple as a stuck thermostat creating a blockage.
    Or water pump vanes have fallen off and coolant isn't flowing properly. From memory some JD pumps use a plastic impellor

    1 Question? Why take W/pump belt off then run it? Kinda making an issue there by not allowing the coolant to flow properly.
    Trout and Tommy like this.
    Life is natures way of keeping meat fresh

  4. #4
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247
    Quote Originally Posted by cambo View Post
    Could even just be something as simple as a stuck thermostat creating a blockage.
    Or water pump vanes have fallen off and coolant isn't flowing properly. From memory some JD pumps use a plastic impellor

    1 Question? Why take W/pump belt off then run it? Kinda making an issue there by not allowing the coolant to flow properly.
    To see if the pipe is blocked somewhere and the pump is building up pressure, that was my first guess. Without the pump running the only other way getting pressure in there would be engine leak.
    Cooling system was cold and engine only ran 30 sec and started pushing out coolant.
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  5. #5
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247
    Quote Originally Posted by Fireflite View Post
    @boarFreak

    As @Mauser308 has mentioned or maybe one of the following, and in the order of cheap to expensive to replace

    1, head gasket
    2, cracked head
    3, cylinder liner damage

    You can by test kits that will indicate if its combustion gas in the coolant.
    I don't think they are an over head cam engine. If that is the case, removing the head should be a pretty simple operation and you wouldn't need to worry about any timing issues.
    You would need to remove the head to diagnose any of the 3 issues above!
    You will have to do your home work though as the bolts may be "torque to yield" so would need to be replaced.

    Check out You Tube to see if there is anything on there about head gasket replacement on these engines.

    If it was mine, I'd be giving it a go! I reckon an SJ413 would be more of a mission!

    Good Luck
    Thanks.
    It is overhead, rocker arms and everything have to come off.
    Forgot to mention the return hose between engine and radiator filled up with air too when tested without pump running.
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  6. #6
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    Quote Originally Posted by Boar Freak View Post
    To see if the pipe is blocked somewhere and the pump is building up pressure, that was my first guess. Without the pump running the only other way getting pressure in there would be engine leak.
    Cooling system was cold and engine only ran 30 sec and started pushing out coolant.
    No all it will do is cause an air blockage and the temp rises quickly and then blows out the coolant.
    Life is natures way of keeping meat fresh

  7. #7
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    Quote Originally Posted by Boar Freak View Post
    Thanks.
    It is overhead, rocker arms and everything have to come off.
    Forgot to mention the return hose between engine and radiator filled up with air too when tested without pump running.
    Coolant wont flow with the pump not running and then as the temp rises any air turns locked in anywhere in the system will to steam and blow out the coolant.
    If you can get a pressure tester and pressurise the cooling system to see if there's a leak. Can remove the glowplugs and crank over to see if coolant leaking into combustion area.
    Life is natures way of keeping meat fresh

  8. #8
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247
    Quote Originally Posted by Mauser308 View Post
    I'd be looking to the previous work myself - i.e. what has changed? In this case the work done was changing the water pump - and that's part of the system that is misbehaving now I'd put money on something not done right. Also another option once you've diagnosed is a dose of irontite (salesmans head gasket replacement) might seal something up if it's leaking combustion gas.

    For a leak to be doing what you say it's a fairly substantial leak i.e. straight out of somewhere under pressure like a chamber. Considering that the coolant system is pressurised the coolant system is getting considerably overpowered to be taking that much gas. If you aren't getting coolant going the other way then I'm picking that if it isn't related to the water pump job it's from a water cooled something like a turbo that's got exhaust gas at high pressure right next to a coolant passage.
    It was going ok until yesterday.
    The turbo is hooked to the oil system.
    The pump job was done by a proper tractor service firm so I hoped they did a proper job.
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  9. #9
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247
    Quote Originally Posted by cambo View Post
    No all it will do is cause an air blockage and the temp rises quickly and then blows out the coolant.
    Would it heat up enough in 30 sec? Will have to look around if anyone have a tester in my hood.
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  10. #10
    Gkp
    Gkp is offline
    Member
    Join Date
    May 2018
    Location
    Queenstown
    Posts
    1,831
    Try warming it up from cold with the radiator cap off. May have an air lock

  11. #11
    Member
    Join Date
    May 2018
    Location
    Porirua
    Posts
    1,336
    Do you have a compressor, I have just done a cylinder head on my mates land Cruiser, I have an adapter that fits in most glow plugs and a few for spark plugs you can borrow. You simply put compressed air into the cylinder and if the radiator blows bubbles it’s a gasket or cracked head and you then also know which cylinder is the problem. I like to know what’s wrong before I remove anything.
    How much above the Hutt are you and is it the one near Wellington. I’m happy to assist. James
    Trout, gadgetman, Bill999 and 4 others like this.
    Remember the 7 “P”s; Pryor Preparation Prevents Piss Poor Performance.

  12. #12
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247
    Quote Originally Posted by 2post View Post
    Do you have a compressor, I have just done a cylinder head on my mates land Cruiser, I have an adapter that fits in most glow plugs and a few for spark plugs you can borrow. You simply put compressed air into the cylinder and if the radiator blows bubbles it’s a gasket or cracked head and you then also know which cylinder is the problem. I like to know what’s wrong before I remove anything.
    How much above the Hutt are you and is it the one near Wellington. I’m happy to assist. James
    Hi James
    That would be awesome, thanks. Am in Moonshine Valley, about 30 min away from you.
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  13. #13
    Member
    Join Date
    Jan 2018
    Location
    kaiapoi
    Posts
    7,124
    Did much the same on my v8 straight after a rebuild.
    Had the head gasket fail on the break in runs.
    Dicked around and made a spark plug adapter but dont really know why. It was 99% a gasket.
    Good permatorque types and it was failing on a couple of cylinders.

  14. #14
    Member Boar Freak's Avatar
    Join Date
    Jul 2012
    Location
    Above the Hutt
    Posts
    1,247
    Quote Originally Posted by Mauser308 View Post
    Big arse suddenly developing air lock...

    In my *limited* tractor experience (mostly marine) I haven't seen many head gaskets shit themselves that quickly i.e. one day fine next day big arse coolant blow like it's decided to be an extra in Free Willy...

    More likely in my humble opinion to either be a crack or something that hasn't sealed up during a repair job done previously. In this case the thing has had work done on the cooling system, so that's highly suspect as a contributing factor. If that little donkey is wet sleeved - it's possible that an air blockage has lead to a hot sleeve and a failed gasket. Seen that once before but it's rare in my book.

    Also unlikely to heat up from cold to coolant blow 120+deg in 30 sec, that's a pressure leak into the coolant system from my experience. And coolant normally goes two ways when there's a leak - so when it's cold there is likely to be a coolant loss to somewhere however small it may be. I don't know anything of that small a JD motor, so I don't have first hand experience of type design flaws (mitsi diesels in some cases had an issue with their small tractor motors where the exhaust side of the head didn't have enough head bolts making them prone to failure and blown head gaskets).

    Yeah 2post's suggestion is good, done that once or twice. Another way is disconnect the injector pump from the fuel supply, and set the exhaust valves to a slight cracked (not enough clearance) to bleed pressure on all but one cylinder. Bar the engine over to ensure it's not going to smack a valve into the piston, and if all is good wind it over on the starter motor. Reset and repeat for all cylinders, one at a time developing pressure and see which one pops smoke as it were...
    I hope its "just a gasket" or something simple ,could live without pouring a heap of money in the machine. Its worse then a pokey.
    This is it.
    https://www.deere.co.nz/en/industria...-m-4-5l-hf280/
    Nothing is tough about having a 70 lb bow and looking like an uncoordinated praying mantis while trying to draw it back.

  15. #15
    Member Sideshow's Avatar
    Join Date
    Apr 2015
    Location
    UK
    Posts
    7,916
    Oh Deer


    Sorry could not help it
    It's all fun and games till Darthvader comes along
    I respect your beliefs but don't impose them on me.

 

 

Similar Threads

  1. Show us ya tractor
    By rambo rem700 in forum Outdoor Transport
    Replies: 181
    Last Post: 18-02-2018, 06:10 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!