Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Night Vision NZ


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 20
Like Tree10Likes

Thread: EGR delete Mazda bt50

  1. #1
    Member
    Join Date
    Feb 2016
    Location
    Bombay
    Posts
    1,042

    EGR delete Mazda bt50

    Hopefully picking up a 2014 model this week. Anyone here done an EGR delete? Also is it worth taking it in for a tune.

    Cheers.

  2. #2
    Banned
    Join Date
    Dec 2021
    Location
    Tauranga
    Posts
    5,143
    Which model are you looking at - the 3.2L? Get a good fuel system service and check if so, and find someone with a decent datalogger that can hook up and see what the fuel system is doing. If you get one that has had crap through it or an injector is kaput it's likely the thick end of 9K. The issue mine has is the fuel pressure modulation valve isn't closing fast enough - it's leading to a pesky limp mode issue which requires the engine to be powered down and restarted to clear. This valve is commonly called the suction control valve, but not what it does. It controls pressure to the injectors, and in my case the ecu is saying ramp pressure down and the valve isn't closing so the pressure is staying sky high and taking it out of specification leading to the error.

    Point there is most mechanical outfits when presented with an issue like that on these common rail engines, will not invest time in diagnosis - they will just replace the injection pump complete and the entire injector and fuel rack setup. Which may or may not fix the issue - so in this case prevention is better. Get em fully checked and serviced so you know what you're getting.
    7mmsaum, veitnamcam, Tommy and 1 others like this.

  3. #3
    Member
    Join Date
    Feb 2016
    Location
    Bombay
    Posts
    1,042
    Sweet. Yes it’s the 3.2l

  4. #4
    Banned
    Join Date
    Jun 2015
    Location
    christchurch
    Posts
    17,992
    i would remove the air intake hose and see how much grud is in the intake manifold too. our triton was literally 1/3 full of goopy tar.
    i found that 2 bottles of "royal egr cleaner" took most of it out. i then fiendishly told the engine management system that it was always below 0 celcius outside and that turned off the egr
    DemocKot and XR500 like this.

  5. #5
    Member JoshC's Avatar
    Join Date
    Apr 2012
    Location
    Southland/Otago
    Posts
    3,728
    Quote Originally Posted by gonetropo View Post
    i would remove the air intake hose and see how much grud is in the intake manifold too. our triton was literally 1/3 full of goopy tar.
    i found that 2 bottles of "royal egr cleaner" took most of it out. i then fiendishly told the engine management system that it was always below 0 celcius outside and that turned off the egr
    You reckon that EGR cleaner works ok then? I have my reservations given how sticky that carbon shit is...but its a 7-9 hour job to pull the intake manifold out of a V8 cruiser motor...
    Next one is definitely getting a catch can plumbed in.
    I'm drawn to the mountains and the bush, it's where life is clear, where the world makes the most sense.

  6. #6
    Member Mathias's Avatar
    Join Date
    Oct 2015
    Location
    Canterbury, home of the big Rakaia Red Stag
    Posts
    4,513
    Yep catch can it a good mod for a new or newish vehicle. Good to fit if you have a dung out first on a higher km engine.
    I bought a catch can & EGR delete kit out of Aussie for my Hilux & fitted it at 45000kms.

    Sent from my SM-S906E using Tapatalk

  7. #7
    Banned
    Join Date
    Jun 2015
    Location
    christchurch
    Posts
    17,992
    Quote Originally Posted by JoshC View Post
    You reckon that EGR cleaner works ok then? I have my reservations given how sticky that carbon shit is...but its a 7-9 hour job to pull the intake manifold out of a V8 cruiser motor...
    Next one is definitely getting a catch can plumbed in.
    i tried several. "royal" worked the best. do it outside on a windy day though!
    took 2 bottles @$25 each, wasnt like a mirror clean etc but took 90% of the crud out
    JoshC likes this.

  8. #8
    Banned
    Join Date
    Dec 2021
    Location
    Tauranga
    Posts
    5,143
    That is definitely one time prevention is better than cure... Shame of it is I was not allowed to do that with the extended warranty I got with mine, probably wouldn't do that again.

    The other thing is change the damn fuel filter out every bloody service! It is cheap insurance and the tech gets to physically look at the state of it and solve any bug problems before they start. And if you ask your mechanic to do this, don't do it verbally and believe them. Bastards didn't for me and claimed to have no record of the conversation and still tried to bill me for $9k to change the fuel system out when they found bug. They've had the tank out 4 times on that vehicle now, and still they blame me for not getting the servicing done to spec. They won't see the vehicle back, I'm happy to work with anyone but stating one thing and doing the opposite just pisses me off...

  9. #9
    Banned
    Join Date
    Jun 2015
    Location
    christchurch
    Posts
    17,992
    with the mitsi i turned it off electronically, it could be returned to "standard" in 2 minutes.
    we now have a 22 d-max. might look at what the same mod would entail on that one

  10. #10
    Member
    Join Date
    Oct 2020
    Location
    Christchurch
    Posts
    116
    I've put 200k on my 2012 3.2l Bt 50. It's been a good run. Couple of little electrical niggles. BCM decided it didn't like the trailer wiring loom a couple of times - lost all brake lights. Supercheap Auto charge $25 to put a scan tool on it and clear the error code. Mazda dealers in Chch charged over $100 and wouldn't/couldn't tell me what the problem was. Independent auto sparky sorted me out with that bit of advice.
    Rubber intercooler pipe split twice. Replaced it both sides with an aftermarket hard pipe kit that was cheaper than one OEM replacement rubber pipe. Had Diesel Tune NZ do a remap for me over 100k ago. Excellent performance upgrade for the $1200 it cost. Then I fitted an electronic throttle controller and that was the best $300 spent. What you think is turbo lag is engineered slow throttle response to help fuel efficiency. With the next ute I'd do the throttle controller first and possibly not worry about the ecu remap.
    Also suspension, bar work, snorkel etc etc... none of which helped how much fuel it drinks.
    JoshC and Tuckerbox like this.

  11. #11
    Member Bobba's Avatar
    Join Date
    May 2018
    Location
    Ngaruawahia
    Posts
    1,299
    Quote Originally Posted by BMcB View Post
    I've put 200k on my 2012 3.2l Bt 50. It's been a good run. Couple of little electrical niggles. BCM decided it didn't like the trailer wiring loom a couple of times - lost all brake lights. Supercheap Auto charge $25 to put a scan tool on it and clear the error code. Mazda dealers in Chch charged over $100 and wouldn't/couldn't tell me what the problem was. Independent auto sparky sorted me out with that bit of advice.
    Rubber intercooler pipe split twice. Replaced it both sides with an aftermarket hard pipe kit that was cheaper than one OEM replacement rubber pipe. Had Diesel Tune NZ do a remap for me over 100k ago. Excellent performance upgrade for the $1200 it cost. Then I fitted an electronic throttle controller and that was the best $300 spent. What you think is turbo lag is engineered slow throttle response to help fuel efficiency. With the next ute I'd do the throttle controller first and possibly not worry about the ecu remap.
    Also suspension, bar work, snorkel etc etc... none of which helped how much fuel it drinks.
    Hey @BMcB what throttle controller did you get?

  12. #12
    Member
    Join Date
    Oct 2020
    Location
    Christchurch
    Posts
    116
    It's a Hike It X9.
    There's a few different ones on the market. I think they all work the same. Only takes a few minutes to fit and less to remove if you need to.

  13. #13
    Member
    Join Date
    Feb 2016
    Location
    Bombay
    Posts
    1,042
    Quote Originally Posted by BMcB View Post
    I've put 200k on my 2012 3.2l Bt 50. It's been a good run. Couple of little electrical niggles. BCM decided it didn't like the trailer wiring loom a couple of times - lost all brake lights. Supercheap Auto charge $25 to put a scan tool on it and clear the error code. Mazda dealers in Chch charged over $100 and wouldn't/couldn't tell me what the problem was. Independent auto sparky sorted me out with that bit of advice.
    Rubber intercooler pipe split twice. Replaced it both sides with an aftermarket hard pipe kit that was cheaper than one OEM replacement rubber pipe. Had Diesel Tune NZ do a remap for me over 100k ago. Excellent performance upgrade for the $1200 it cost. Then I fitted an electronic throttle controller and that was the best $300 spent. What you think is turbo lag is engineered slow throttle response to help fuel efficiency. With the next ute I'd do the throttle controller first and possibly not worry about the ecu remap.
    Also suspension, bar work, snorkel etc etc... none of which helped how much fuel it drinks.
    Came with a throttle controller and all these bits. Name:  F3E6A3AA-21A0-4479-8385-476DB7410080.jpeg
Views: 803
Size:  805.4 KB
    BRADS likes this.

  14. #14
    Banned
    Join Date
    Dec 2021
    Location
    Tauranga
    Posts
    5,143
    Quote Originally Posted by BMcB View Post
    I've put 200k on my 2012 3.2l Bt 50. It's been a good run. Couple of little electrical niggles. BCM decided it didn't like the trailer wiring loom a couple of times - lost all brake lights. Supercheap Auto charge $25 to put a scan tool on it and clear the error code. Mazda dealers in Chch charged over $100 and wouldn't/couldn't tell me what the problem was. Independent auto sparky sorted me out with that bit of advice.
    Rubber intercooler pipe split twice. Replaced it both sides with an aftermarket hard pipe kit that was cheaper than one OEM replacement rubber pipe. Had Diesel Tune NZ do a remap for me over 100k ago. Excellent performance upgrade for the $1200 it cost. Then I fitted an electronic throttle controller and that was the best $300 spent. What you think is turbo lag is engineered slow throttle response to help fuel efficiency. With the next ute I'd do the throttle controller first and possibly not worry about the ecu remap.
    Also suspension, bar work, snorkel etc etc... none of which helped how much fuel it drinks.
    I dunno, that intercooler pipe issue is something I've never heard happen on a manual box one - no idea why that would be though. Yes on the throttle lag, but again it is much worse on the auto's. the throttle controller does less than the remap on the manuals, but you're rolling the dice on the dual mass flywheel with the manual!

    I have a bluetooth dongle, can read/clear fault codes and also live-report with gauges on most things the ECU does. One thing I've noticed though is that the dongle seems to turn the limp mode and error coding off which is weird. You can see the issue that is causing the coding and associated limp mode on the gauges clear as, but while you can see it the ECU doesn't drop the limp mode or codes. Must be something in the software when the OBDII port is active.

  15. #15
    Member
    Join Date
    Mar 2018
    Location
    Darfield
    Posts
    421
    Quote Originally Posted by No.3 View Post
    I dunno, that intercooler pipe issue is something I've never heard happen on a manual box one - no idea why that would be though. Yes on the throttle lag, but again it is much worse on the auto's. the throttle controller does less than the remap on the manuals, but you're rolling the dice on the dual mass flywheel with the manual!

    I have a bluetooth dongle, can read/clear fault codes and also live-report with gauges on most things the ECU does. One thing I've noticed though is that the dongle seems to turn the limp mode and error coding off which is weird. You can see the issue that is causing the coding and associated limp mode on the gauges clear as, but while you can see it the ECU doesn't drop the limp mode or codes. Must be something in the software when the OBDII port is active.
    Flatmate just pulled up from the Ford dealer, his manual ranger had split intercooler pipe so went limp mode. Early model no reverse camera etc. Over 200ks on the clock.

 

 

Similar Threads

  1. Flatdecks for Ranger/BT50 PX
    By Tentman in forum Outdoor Transport
    Replies: 6
    Last Post: 25-04-2019, 01:33 PM
  2. Mazda BT50
    By HNTMAD in forum Hunting
    Replies: 19
    Last Post: 27-05-2015, 09:43 PM
  3. Anyone got a new Mazda BT50?
    By kiwijames in forum Outdoor Transport
    Replies: 53
    Last Post: 25-04-2012, 06:50 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!