Axe handles

Ok - axe handles.

Who has a decent stock of the good ones - like the imported Columbia brand from the states? They have a decent size to the haft so they can actually be shaped down enough to fit a full size head like a Plumb, Kelly or Hytest with the 60x24mm oval eye...

I used to get them from the local emporium store but they've run out, and the local hardware shops like Mitre10 seem to just have the locally made ones that are 90cm handles with a haft that fits a hatchet head. It's a bit ridiculous, I have never seen an axe head with an eye that small (45mm by 16mm) even on the imported Chinese cheap stuff. The outfit that makes them has shaped them way too much, should have left them a straight oval rather than taking them down to the tiny oval they are now. Not that bad a piece of wood as far as handles go too which makes it all the more disappointing.

I'm not really set up to quickly make handles from a chunk of tree and most of my chunks of tree are 30cm long for fitting into a firebox haha. Now I guess I could use a chainsaw and hack a piece out of the remains of a bloody dense fir I have here, but it seems a little bit less than traditional.

Quote:

---

Originally Posted by No.3

Ok - axe handles.

Who has a decent stock of the good ones - like the imported Columbia brand from the states? They have a decent size to the haft so they can actually be shaped down enough to fit a full size head like a Plumb, Kelly or Hytest with the 60x24mm oval eye...

I used to get them from the local emporium store but they've run out, and the local hardware shops like Mitre10 seem to just have the locally made ones that are 90cm handles with a haft that fits a hatchet head. It's a bit ridiculous, I have never seen an axe head with an eye that small (45mm by 16mm) even on the imported Chinese cheap stuff. The outfit that makes them has shaped them way too much, should have left them a straight oval rather than taking them down to the tiny oval they are now. Not that bad a piece of wood as far as handles go too which makes it all the more disappointing.

I'm not really set up to quickly make handles from a chunk of tree and most of my chunks of tree are 30cm long for fitting into a firebox haha. Now I guess I could use a chainsaw and hack a piece out of the remains of a bloody dense fir I have here, but it seems a little bit less than traditional.

---

I know the racing boys used kanuka years ago but I was told selection of the kanuka was key to a good one - likely lost art

Quote:

---

Originally Posted by No.3

Ok - axe handles.

Who has a decent stock of the good ones - like the imported Columbia brand from the states? They have a decent size to the haft so they can actually be shaped down enough to fit a full size head like a Plumb, Kelly or Hytest with the 60x24mm oval eye...

I used to get them from the local emporium store but they've run out, and the local hardware shops like Mitre10 seem to just have the locally made ones that are 90cm handles with a haft that fits a hatchet head. It's a bit ridiculous, I have never seen an axe head with an eye that small (45mm by 16mm) even on the imported Chinese cheap stuff. The outfit that makes them has shaped them way too much, should have left them a straight oval rather than taking them down to the tiny oval they are now. Not that bad a piece of wood as far as handles go too which makes it all the more disappointing.

I'm not really set up to quickly make handles from a chunk of tree and most of my chunks of tree are 30cm long for fitting into a firebox haha. Now I guess I could use a chainsaw and hack a piece out of the remains of a bloody dense fir I have here, but it seems a little bit less than traditional.

---

not being stupid - what about steel pipe - shape with pipe bender - heat and flatten to get nice shape to hold - weld head on- ya wont break it

I was buying them from tuatahi. They turn them in-house for their racing axes.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Barry the hunter

not being stupid - what about steel pipe - shape with pipe bender - heat and flatten to get nice shape to hold - weld head on- ya wont break it

---

After I broke the wooden handle on a sledge hammer I replaced it with a length of water pie.
It was the most hideous thing to use. Hurt my hands like hell due to jarring. So even if wood seems solid it still gives a cushioning effect. The water pipe didn't.
OK for occasional use only.

I've got same problem. Full size axe & I like a slightly shorter handle. Good luck with that.
Best place has been Wrightsons. But eye is pretty marginal & no 34 inch.

Quote:

---

Originally Posted by MSL

I was buying them from tuatahi. They turn them in-house for their racing axes.


Sent from my iPhone using Tapatalk

---

I have a Tuatahi work axe and can vouch for their handles. They have a rather larger throat, grip and knob than most. It makes for a very comfortable axe. They use hickory.

Quote:

---

Originally Posted by zimmer

After I broke the wooden handle on a sledge hammer I replaced it with a length of water pie.
It was the most hideous thing to use. Hurt my hands like hell due to jarring. So even if wood seems solid it still gives a cushioning effect. The water pipe didn't.
OK for occasional use only.

---

I did not say it would be comfortable - but we did put a few with pipe handles out at remote huts many years ago when we got pissed of with trampers continually breaking handles ( note I did not blame hunters and yes racist of me ) they lasted but the blade thats another story

Quote:

---

Originally Posted by zimmer

After I broke the wooden handle on a sledge hammer I replaced it with a length of water pie.
It was the most hideous thing to use. Hurt my hands like hell due to jarring. So even if wood seems solid it still gives a cushioning effect. The water pipe didn't.
OK for occasional use only.

---

Funny how it goes ah.

I broke the handle on my lump hammer.

Replaced it wit a bit of the broken axe handle !

Hickory I think so no jarring [emoji106]

Sent from my SM-G950F using Tapatalk

Quote:

---

Originally Posted by kukuwai

Funny how it goes ah.

I broke the handle on my lump hammer.

Replaced it wit a bit of the broken axe handle !

Hickory I think so no jarring [emoji106]

Sent from my SM-G950F using Tapatalk

---

What happened to the bins of American Hickory axe handles and wedges that hardware shops used to have.

Check out leech wood products they’re a small handle manufacturing co just south of Christchurch but I think there’s another crowd near Auckland doing similar.

Quote:

---

Originally Posted by zimmer

What happened to the bins of American Hickory axe handles and wedges that hardware shops used to have.

---

what happened to the bloody good old hardware shops

Quote:

---

Originally Posted by Southcity

I have a Tuatahi work axe and can vouch for their handles. They have a rather larger throat, grip and knob than most. It makes for a very comfortable axe. They use hickory.

---

They are also relatively short compared to most of those available, which I like.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by Barry the hunter

what happened to the bloody good old hardware shops

---

That is the question!! Have been doing the rounds in Dunedin and Invers and having no joy finding hatchet or rake/hoe handles. Two full sized axe handles and some sledge handles in Mitre10 Invers but that’s it. Having been keeping an eye out whenever I’m in the big smokes but nothing for months.

Go bush and find a good stand of Manuka and harvest your own. My favourite sledgy has a 60cm Manuka handle, its awesome, Has a bit of texture to give good grip and it isn't slippery when it gets wet.

Just found out the outfit that makes Columbia brand handles is no more, brought out by Seymour Handles who don't appear to export here. The best options look like either Tuatahi at $100, roll your own which is likely more than $100 worth by the time you fluff about finding them or Bahco branded handles which are imported Ash by the look of them. If you don't want an 800mm handle, well...

The Euro pattern handles look OK but are looking like the only available option that isn't supplied with the kid's head sized haft. Those mitre 10 handles look like they'd fit into a full sized head eye - sideways. They don't even look like they fit the same branded axe heads that they sit next to on the shelf! They look more like something that would go into a tack hammer rather than an axe...

https://engineeredforaxemen.com.au/p...ing-axe-handle
These are great handles, pricey though. Made in Australia with local timber. Come with a roll pin and alloy wedge.


Sent from my iPhone using Tapatalk

beautiful axes they make too....

Quote:

---

Originally Posted by Micky Duck

beautiful axes they make too....

---

Your not wrong Mickyhttps://uploads.tapatalk-cdn.com/202...8560823a06.jpg
https://uploads.tapatalk-cdn.com/202...5956a129e5.jpg


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by MSL

https://engineeredforaxemen.com.au/p...ing-axe-handle
These are great handles, pricey though. Made in Australia with local timber. Come with a roll pin and alloy wedge.


Sent from my iPhone using Tapatalk

---

Saw those, dearer than Tuatahi though by the time you roll courier in. No really easy option, those Bahco ones are about half the price and a similar profile...

Quote:

---

Originally Posted by MSL

Your not wrong Mickyhttps://uploads.tapatalk-cdn.com/202...8560823a06.jpg
https://uploads.tapatalk-cdn.com/202...5956a129e5.jpg


Sent from my iPhone using Tapatalk

---

Almost look like the 7mm-08 to Tuatahi's .308 - ballistic twins... Have seen comment from overseas that they are considered equals in the wood and the grind and sharpening on each matters more.

Funny reading this thread as just today I put a 550mm Kanuka handle on a fencing hammer - a Cyclone 2 1/2 lb head.
Have never made a proper handle like that before, came out very well and very strong. Easy to shape with a flapper disk. A lot of Kanuka has a bit of bow sweep at the bottom to give it that Axe handle shape