Gun Smith - top of SI

Printable View

04-03-2018, 01:54 PM
Sarvo

2 Attachment(s)

Gun Smith - top of SI

Does anyone know of a Gun Smith or someone capable of doing a recoil pad fit onto a wooden stock Baikal
Tried myself and cocked up 1st one
Have the recoil pad (new one) but want it done professionally this time :P
I live Marlborough - but can go Nelson way too

Thanks in advance
Peter

Attachment 83622

Attachment 83623
04-03-2018, 02:00 PM
Micky Duck

leave it slightly oversized..... freeze and grind is the proper method I believe... you should be able to do it just remember measure twice and cut once....in my case measure three times.
04-03-2018, 02:03 PM
Sarvo

Quote:

Originally Posted by Micky Duck

leave it slightly oversized..... freeze and grind is the proper method I believe... you should be able to do it just remember measure twice and cut once....in my case measure three times.

No - tried it once and ruined one recoil pad already
Woolshed emery grinder will do the job - but really need to make a jig/blank encase hit the stock
Also not easy getting the level (or comb) correct angle off top and bottom of pad to match angle of stock

Happy yo pay an expert
04-03-2018, 02:05 PM
Micky Duck

for what its worth a slip on pad works just as well.....thats what goes on mine lol.
04-03-2018, 02:07 PM
Micky Duck

oh and you already have pattern...use the hard buttplate that you took off it. mark it out on replacement and go from there....or courier it down to Robbie and team in chch.
04-03-2018, 02:08 PM
MSL

Definitely don’t grind it while it’s still attached, haha.
04-03-2018, 02:08 PM
Sarvo

Quote:

Originally Posted by Micky Duck

for what its worth a slip on pad works just as well.....thats what goes on mine lol.

Yes - got one of those - but this Baikal is very small butt end
Have a China knock off coming via Free Shipping (so prob get it after Roar)
They are good - but this little rifle deserves better
04-03-2018, 02:10 PM
Sarvo

Quote:

Originally Posted by MSL

Definitely don’t grind it while it’s still attached, haha.

No
I did the 1st one clamped onto the old one that had the hard plate still attached, but cocked up the top and bottom angle/line off stock
04-03-2018, 02:12 PM
nor-west

Dave Ward, ph 03 543 3777, of Dovedale Road, Nelson.
04-03-2018, 02:17 PM
veitnamcam

Quote:

Originally Posted by nor-west

Dave Ward, ph 03 543 3777, of Dovedale Road, Nelson.

Wakefield, Nelson ;)
04-03-2018, 02:17 PM
Sarvo

Quote:

Originally Posted by Micky Duck

oh and you already have pattern...use the hard buttplate that you took off it. mark it out on replacement and go from there....or courier it down to Robbie and team in chch.

I wanted Robbie to do it when they did the SUP last month - but she said Robbie sick and not doing pads ???
Bit odd ah ?
04-03-2018, 02:22 PM
Sarvo

Quote:

Originally Posted by veitnamcam

Wakefield, Nelson ;)

Thanks @nor-west and @veitnamcam
I thought there was a local - just got that sleeping bag thanks to @StrikerNZ and its in Nelson too
Had an offer already from a Forum Member to do it - but needs to be sent Waikato and he's a busy working boy and needs more time to practice with his 30-30 - so I thank him immensely (cheers Derek) but will give Dave in Wakefield a bell tomorrow
04-03-2018, 02:34 PM
mikee

Quote:

Originally Posted by Sarvo

Thanks @nor-west and @veitnamcam
I thought there was a local - just got that sleeping bag thanks to @StrikerNZ and its in Nelson too
Had an offer already from a Forum Member to do it - but needs to be sent Waikato and he's a busy working boy and needs more time to practice with his 30-30 - so I thank him immensely (cheers Derek) but will give Dave in Wakefield a bell tomorrow

Let me know if you are coming this way, I have something for ya too
04-03-2018, 02:40 PM
Sarvo

Quote:

Originally Posted by berg243

put it on the rifle and mark pad with a pen held against the stock this will give you a start cut that will allow some leeway remove from stock and do your rough cut then reattach to stock and wrap a layer of pvc tape 2 or 3 widths wide onto stock then a layer of masking tape over it now use an orbital sander with stock held in a clamp or vice so you can look down onto stock and keep sander on the same line as stock .rotate stock around as you do each side then do the top and heel as soon as you touch masking tape remove and put on new layer once down to same level as masking tape remove it and use finer grade sandpaper till same level as pvc tape once down to pvc tape slightly angle sander so you can take a little bit more off with out touching tape about 1mm then just do a light cut with sander more following contour but keep edge of sander just off edge of wood or you can remove from stock and just finish on a bench sander by colouring the pad with ink and just removing enough to get rid of the ink.you can also use a rasp file to do the first cut

I would have tried that way if had a belt sander.
I did as above clamped onto old pad plate and used a buffer pad on angle grinder which did a fine/smooth finish to pad
But as I said - the angle/line off the stock top and bottom is a trick for me without taking huge risk (to me anyways) of leaving attached to stock and slipping and guaging into the lovely grained wood of Baikal
No - I will get Gunsmith Nelson to do it
Throw another Goldfish to the cat - as we say

Those buffer pads are bloody great for buffing up old knives/machetes/meat clevers etc
Polish up like new !!
04-03-2018, 02:43 PM
Sarvo

Quote:

Originally Posted by mikee

Let me know if you are coming this way, I have something for ya too

Yes - its only a matter of unscrew old one on my way over and attach new one on way home - yes ??
And plug it in behind the dash ??
You don't need box etc ?

I will talk with Dave tomorrow and may send stock over and then do pick up - see how busy he is.
04-03-2018, 02:52 PM
mikee

Quote:

Originally Posted by Sarvo

Yes - its only a matter of unscrew old one on my way over and attach new one on way home - yes ??
And plug it in behind the dash ??
You don't need box etc ?

I will talk with Dave tomorrow and may send stock over and then do pick up - see how busy he is.

Pretty much that. just been a bit awkward to do with way things are at mo, no work over your way either
04-03-2018, 08:46 PM
timattalon

If you have no joy, I have a gunsmith type person here who can do this. He has done several before. Is it a normal Baikal stock? Is it still standard and not shortened? I could possibly get a recoil fitted to size to one of our new Baikals and arrange to get it to you. That way there is no shipping rifle parts too and fro. So buy a recoil pad from us, pay for it to be sized and shipped to you and done....How does that sound?
04-03-2018, 08:54 PM
Sarvo

Quote:

Originally Posted by timattalon

If you have no joy, I have a gunsmith type person here who can do this. He has done several before. Is it a normal Baikal stock? Is it still standard and not shortened? I could possibly get a recoil fitted to size to one of our new Baikals and arrange to get it to you. That way there is no shipping rifle parts too and fro. So buy a recoil pad from us, pay for it to be sized and shipped to you and done....How does that sound?

Cheers
Will get back to after tomorrow if I have no joy in Nelson