Thread: Damn It! Lost load data.

Update: Still couldn't find the data I was looking for but I've recently been offered a Lee 1oz slug mold and some Unique powder, plenty of data for the slug and powder but the data data is only for 1450fps @ 10,000psi, I've love to make a reduced load at around 1200fps with less pressure and less recoil. Anyone tried this?

Why can't you just reduce the charge until you get the velocity you want?
Or interchange data for any 1 oz shot load at the velocity you want?
With a plastic wad it shouldn't matter wether you are pushing 1 oz of shot down the barrel or a 1 oz slug.

Originally Posted by Bob Da Browning

I have been using Win AA compression formed hull with Win 209 Win AA12 11/8 wad cut petals to length, 20g felt under 1oz lee keydrive, 21.6grains AS50n. I use this in Rem 1187 slug gun & it goes great on rabbits, hares & possums. I started at 21grains which was nice & light but am now at 21.8grains.

@Bob Da Browning. What colour are the 1 1/8 wads? I've pick up a 1oz Lee slug mold and might try you recipe. Any idea of the velocity? how was the recoil?

This is the state of a wad from recent testing of slugs loaded as per ADI's load data. This wad stayed with the slug until it hit the 25m target and bounced off. There's a clear indentation caused by the slugs base.

the wads I used were White, without the felt base I had the indentation like yours. Use a felt/cork base & trim the petals back to the shoulder of the slug, this improved the accuracy of mine heaps. 21grains felt like 1200-1225fps (just cycling the action on the Remington 1187) & 21.8 feels like 1300-1330fps (feels like the fast trap loads I use & blows up rabbits great at 50yds). I use a fold crimp. I shoot Trap & Skeet so compare recoil & speed to the pattern sheet, at 50m the with 21.8grain the slug goes through the wooden pallet & folds the waratah in half almost cutting it off.

Originally Posted by Bob Da Browning

the wads I used were White, without the felt base I had the indentation like yours. Use a felt/cork base & trim the petals back to the shoulder of the slug, this improved the accuracy of mine heaps. 21grains felt like 1200-1225fps (just cycling the action on the Remington 1187) & 21.8 feels like 1300-1330fps (feels like the fast trap loads I use & blows up rabbits great at 50yds). I use a fold crimp. I shoot Trap & Skeet so compare recoil & speed to the pattern sheet, at 50m the with 21.8grain the slug goes through the wooden pallet & folds the waratah in half almost cutting it off.

@Bob Da Browning thanks for your input. I did have some homemade cork nitrocards but didn't use them, Pushed the slug slighty too high up the hull and couldn't get a decent foldcrimp. Was that 21 grains of AP70N?

I used AS50N as I couldnt get AP70

Originally Posted by Bob Da Browning

the wads I used were White, without the felt base I had the indentation like yours. Use a felt/cork base & trim the petals back to the shoulder of the slug, this improved the accuracy of mine heaps. 21grains felt like 1200-1225fps (just cycling the action on the Remington 1187) & 21.8 feels like 1300-1330fps (feels like the fast trap loads I use & blows up rabbits great at 50yds). I use a fold crimp. I shoot Trap & Skeet so compare recoil & speed to the pattern sheet, at 50m the with 21.8grain the slug goes through the wooden pallet & folds the waratah in half almost cutting it off.

@Bob Da Browning I tried 21gn of AS50n, still kicked a bit. I shot a three shot group @ 50m, two hit 2" apart but one hit 5" low, possible flyer or something wrong with load. I tried a reduced load of 26gn down from ADI's recommend 28.1gn, recoil felt a lot worst, knocked the wind out of me a bit but a nice 2" group

fill the cavity in base of slug with something like silicon..it wont grab the wad the same anymore