Printable View
If your interested in a build, 'rebarrel, barrel threading or most things rifle related
Post it up here for a quote or pm if you would like to do it that way.
Only takes few minutes to ask an you might be surprised with the out come when there is no middle man, an my interests are in happy customers with good bang for the buck :)
That's what I tell all the girls....Quote:
Originally Posted by tui_man2
But did they come back for 2nds?Quote:
Originally Posted by Wirehunt
:thumbsup: Does it work?Quote:
Originally Posted by Wirehunt
Dont think the wife would like me trying it................
Looking for a rough price on a 338 edge
28inch Barrel fitted to a T3 action
I will supply action.
Benefits of going trueflite vs vulcan?
Price difference?
Just want a ball park figure. Cheers
Vulcan don't currently do a 338 tube, so would be trueflight, shillen or lilja tube.Quote:
Originally Posted by PerazziSC3
And I'm not real keen to do something that big on the t3 action sorry. Others might be tho? I could trade your action on new rem700 action
Sent from my GT-I9300T using Tapatalk 2
Rough price to bed and stiffen the forend on a Tikka T3, and do you offer a load development service?
Lachlan
To alloy pillar an bed action and stiffen the fore end would be 365 an freighted back. I do do loads but price depends on if I supply everything or you do? Base price of 180 an goes up from thereQuote:
Originally Posted by .22-250 everything
Sent from my GT-I9300T using Tapatalk 2
If I had an old BSA .243, how much to re-barrel into a 338 Fed, threaded and put a weaver rail on top?
Sorry for the delay here never seen it sorry.Quote:
Originally Posted by Vapour
If you had a old bsa to make it into a 338fed an rail would be, depending on barrel
barrel fitted an chambered starts from $690
threaded an cap is $70
rail depending if want cant etc milled into is starts at $110
thankyou
Thanks TM2, do you also still make suppressors? in 338?
Sent from my GT-I9100 using Tapatalk 2
I do still make them to mate in alloy mainly at moment still doing odd carbon one but supply of quality has been hard at having to test each batch and not doing enough to warrant buying huge lots, since I'm only one man demand is hard to keep up with.Quote:
Originally Posted by Vapour
Sent from my GT-I9300T using Tapatalk 2
Hi what price would it be to put a suppresser on a 22.250 Tikka T3. thanks.
For one of mine mate or another brand?Quote:
Originally Posted by Nana The Flats
Alloy one of mine is 450 fitted an freighted back. Includes thread cap and recrown
Sent from my GT-I9300T using Tapatalk 2
Hey Abe, I have a wee project on the go, I have a 6.5x55 howa action and barrel I want turned down to about a #2 contour, shortened to 20", fluted and all the metal work done in cerakote then dropped into an unfinished stock I have here that needs the barrel channel cut out and action bedded.
Let me know if that's possible.
Cheers,
Year mate it can be done I'll send you a text shortly and will give you a buzz when it suits you. Just going to burn out see if can get anything goingQuote:
Originally Posted by Tahr-Bound
Sent from my GT-I9300T using Tapatalk 2
Abe, what do you charge to
Flute a barrel
Spiral flute a bolt and lighten the bolt handle
Cheers, Stu.
Hey stuQuote:
Originally Posted by stug
300 a barrel that's flute blast an re crown, an 110 for the bolt but I don't do spiral unless I have 5or so to do as for my set up its not cost affective for one
Sent from my GT-I9300T using Tapatalk 2
Cheers Abe, I'm pretty keen on the spiral flute on the bolt, just for the looks.
No worries stu. I can get it done will end up been the same as others at the 120 130 markQuote:
Originally Posted by stug
Sent from my GT-I9300T using Tapatalk 2
Are you able to do a 300 blackout barrel swap on a NEA ar15?
I just got an done one but if brought the reamer off me as it's not one I thought I'd do again I could ask to hire it back.Quote:
Originally Posted by GregNZ101
Failing that it's probably a no sorry as . Don't do bugger all ar15 stuff sorry. I'll ask tho
Sent from my GT-I9300T using Tapatalk 2
Sorry mate he's on sold the reamer as well. Spanners is the ar man so might pay to talk to him?Quote:
Originally Posted by GregNZ101
Sent from my GT-I9300T using Tapatalk 2
how much to ream standard t3 barrel from 6.5x55 to AI, plus dies to suit or can i give you mine to modify ?
Sorry mate never seen this. 130 to ream an set back chamber. Am dies I can give you price tomorrow for dies would be around 140ish for redding dies, your dies will be hard as hell.Quote:
Originally Posted by scoped
Sent from my GT-I9300T using Tapatalk 2
Re-barreling a Lee Enfield no4 mk2 with a krieger barrel? unless there are other options like a new one made in NZ or ex-surplus?
Ball park figure is close enough for now.
Cost to drill, tap and setup a PU sniper mount to a M44 Mosin Nagant. My gun and mount. 2 position pins and 2 screws with loctite unless you advise to use its locking screws.
I assume this is correct, but I suspect he drilled the pin holes too far, I dont think he needed to go through. Not sure yet, I have not found anything better yet on how to do this, as I'd like to be able to still use stripper clips.
Mosin Nagant M1891/30 PU Sniper Rifle Part 4: Drilling, Tapping, and Inletting Overview - YouTube
Ball park figure is close enough for now.
Sorry mate never seen this.Quote:
Originally Posted by steven
I don't have a 303 reamer sorry as I wouldn't use it. I could try and hire one or buy one if you where dead keen.
I'll price a barrel for you one cal I have never looked at sorry but they will be all around the same id think so 670ish for tube and 250 fit, chamber an crown. Am just freight back
Quote:
Originally Posted by steven
I think like you say pins and 2 screws would be enough unless you wanted the locking screws to make it look original?
Mount supplied?
Something have not done either, but not to hard to do.
Would look better not going all way through.
Would be looking at 130 plus extras if you don't have the mount etc that's with pins and screws at this end. Am bit of freight back.
Again sorry for the delay mate
Sent from my GT-I9300T using Tapatalk 2
Hey Mate
Rough Ball Park on Bedding the action and forend, threading for a suppressor/brake (ill supply the supressor most likely), and possibly adjusting the trigger to something a little lighter? Would be on a Rem 700 SP in 7mm mag or 308.
I haven't got the rifle yet, but wouldn't mind knowing what ill be in for when I do purchase.
Thats cool mate sorry for slow reply have been away huntingQuote:
Originally Posted by Brennos
$295 bedding an fore end stiffen
$65 thread,thread cap an re crown. or if supplying suppressor its $140 for stated an fit the suppressor
$60 trigger job
Hi Abe,
I have a Rem mountain rifle in 7mm-08 but I was wanting to re-barrel to .260 AI. What sort of cost would that be? Also do you think the mag is long enough on a Rem S/A to seat the bullets out to a decent length?
Cheers
Scott.
Hey ScottQuote:
Originally Posted by Kudu
That's cool mate, for match barrel fitted an match chambered will be 760, depending what sort of accuracy your after as well it will/might not need a true up as well. The mmagazine will be plenty mate to get them to lands of my reamer an if more room will throat hurts out to suit.
Let me know if you want to know more or have a chat
Abe
Sent from my GT-I9300T using Tapatalk 2
Hi ,Dont know if its your thing or not. But can you reblue a barrel, action and bolt? if so how much? If not can you suggest someone. Cheers.
Thanks for that. I'll do some sums and get back to you later. (Have to add up dies, lapua brass etc that goes with the build.) How much do you think the courier cost will be to get it to/from Wanganui?Quote:
Originally Posted by tui_man2
Cheers.
Hey MateQuote:
Originally Posted by POME
I can but some it comes up mint an some it don't come up as good as I would like, ill point you in the way of status guns they do a nice job on ones I have seen
Cheers mate.Quote:
Originally Posted by tui_man2
i have a rem in 270 how much to turn into a 338 Edge i will get a stock
hey mateQuote:
Originally Posted by nzteza
Heres rough price to give you idea
pm me for more details if you like
Barrel fitted an chambered $900
Bedding alloy pillars an full bed $250
open face an fit sako extractor $150
True action $200
Flute barrel an bolt?
Thread an fit brake?
Cheers Abe
$35 for freightQuote:
Originally Posted by Kudu
PM done an sent mate
Greetings from Seattle. I am looking for the same stock work and bedding on a Sako A7 in .270 WIN. Will probably use the rifle as is over Christmas / New Year in Southland and leave it with my cousin who has a NZ FAL. No real time line for the work as I won't be back until late 2014. Thanks.Quote:
Originally Posted by tui_man2