40mm
Member

3306 Likes

Page 195 of 221 First ... 95145181182183184185186187188189190191192193194195196197198199200201202203204205206207208209 ... Last

• Jump to page:

1. 
   40mm liked post by On thread : Man who shot teen dead in hunting accident 22 years ago loses firearms licence bid

   Yet repeat drunk drivers get their licenses back

   Liked On: 07-07-2018, 08:20 AM

2. 
   40mm liked post by Cordite On thread : Hiding Gun Cabinet Keys

   Hi Russian 22 Yes, heh heh, definite no-no don't braze any key in, tin solder it. Epoxy itself goes quite soft when the real heat is on, but not sure if any solvent will readily dissolve epoxy? ...

   Liked On: 06-07-2018, 06:41 PM

3. 
   40mm liked post by Cordite On thread : Hiding Gun Cabinet Keys

   Boaraxa, Yeah, some things you just won't do. Fair hiding place is down the spine of the good book if it's not a paperback. In oblong paper wrap to give friction so won't fall out. Or hang...

   Liked On: 04-07-2018, 09:36 PM

4. 
   40mm liked post by Taff On thread : Winchesters

   These were found in a safethat had been in a container where the roof had a caved in, they had been there for 15+ years 9057090571

   Liked On: 04-07-2018, 08:22 PM

5. 
   40mm liked post by 308 On thread : Hiding Gun Cabinet Keys

   Easiest space in an existing house is to make a double wardrobe into a single wardrobe but you'd need to hinge an mdf divider inside and change all the trim so would be fairly obvious A big shelf...

   Liked On: 04-07-2018, 08:11 AM

6. 
   40mm liked post by timattalon On thread : Hiding Gun Cabinet Keys

   If you have a burglar alarm in the house, consider spending a few extra dollars and get the gun cabinet fitted with a sensor so if the scum open it then it triggers the alarm. I have taken every...

   Liked On: 04-07-2018, 08:10 AM

7. 
   40mm liked post by Cordite On thread : Hiding Gun Cabinet Keys

   I just have a wee safe with some bolt actions. Seriously, if I had a large / expensive collection it would be worth the fun of rigging a cheap safe out with a few crappy thin wood screws fixing it...

   Liked On: 04-07-2018, 08:09 AM

8. 
   40mm liked post by Sideshow On thread : Hiding Gun Cabinet Keys

   I've but a small cheap combination lock box on the wall next to the safe, which has nothing in it as I know that a swift blow from a hammer can open this safe. It dose have a small note that says...

   Liked On: 04-07-2018, 08:04 AM

9. 
   40mm liked post by Savage1 On thread : Hiding Gun Cabinet Keys

   Most burglaries where guns are taken that I know of, the keys have been found and safe opened. As soon as they see a safe they go all out looking for the keys. I know of a bunch of C-cat guns got...

   Liked On: 03-07-2018, 08:18 PM

10. 
    40mm liked post by Beavis On thread : Hiding Gun Cabinet Keys

    I have my keys on me whenever I am away from home.

    Liked On: 03-07-2018, 07:30 PM

11. 
    40mm liked post by Rushy On thread : One rifle to rule them all

    Pfffftttt laser smaser, Songhurst has a .270.

    Liked On: 03-07-2018, 06:49 PM

12. 
    40mm liked post by Marty Henry On thread : Teaching Kids - Open sights or scope?

    Open sights seem to be easier in my experience with kids especially with a full size rifle. Apeture is better than tangent, "look through the hole and make the birdie sit on the post".

    Liked On: 03-07-2018, 09:00 AM

13. 
    40mm liked post by Micky Duck On thread : A wee project for myself

    keneff does have a point......replica is opposite of authentic...... a replica made to authentic specifications would be more ....ummmm betterer Engrish.... plurry nice workmanship. does anyone do...

    Liked On: 29-06-2018, 05:55 PM

14. 
    40mm liked post by gundoc On thread : A wee project for myself

    Yes, based on 20 years research which included a trip to the Pattern Room collection to examine, photograph and measure originals. My drawings are accurate and I also have some original drawings. I...

    Liked On: 29-06-2018, 05:55 PM

15. 
    40mm liked post by gundoc On thread : A wee project for myself

    I have made special tooling to bore out the receiver by hand. You can't do it in a lathe because of the skinny tool needed and the interrupted cut. I anneal the bolt body and hacksaw to the...

    Liked On: 29-06-2018, 05:52 PM

Page 195 of 221 First ... 95145181182183184185186187188189190191192193194195196197198199200201202203204205206207208209 ... Last

• Jump to page: