7x64
Member

221 Likes

Page 1 of 15 123456789101112131415 Last

• Jump to page:

1. 
   jamie liked post by 7x64 On thread : Real gunsmiths

   Been thinking about this for awhile, and a post by gundoc prompted me. How about we start a list of “real gunsmiths” I.e. folks who will actually manufacture small parts, tune actions, refinish...

   Liked On: 15-05-2024, 06:50 AM

2. 
   Inder liked post by 7x64 On thread : Bino harness suggestions

   They are an Alaska Guide creations with vortex branding. I use one and really like it. Holds binos, rangefinder, earplugs, phone, small torch, havalon blade changer etc, also find it doesn’t get in...

   Liked On: 15-05-2022, 05:13 PM

3. 
   Southhunter liked post by 7x64 On thread : Non Biased hunting clothing advice

   See if army and outdoors have any British waterproof trousers in stock. $60 I think they were brand new, not super light but cheap and cheerful and likely more durable than hunting gear.

   Liked On: 03-01-2022, 09:00 PM

4. 
   Moa Hunter liked post by 7x64 On thread : Binos $600 or under?

   https://www.adorama.com/siibl832.html Well under 400, but I would take these over the vortex any day of the week.

   Liked On: 27-12-2021, 03:22 PM

5. 
   Hahn liked post by 7x64 On thread : Advice please: boot/crampon compatibility

   Unless you intend to get into full on alpinism, perhaps something a bit lighter and simpler might be the go. These might fit the bill? ...

   Liked On: 19-12-2021, 10:01 AM

6. 
   Stocky liked post by 7x64 On thread : Urgent Message For All Lake Lyndon Target Shooters

   Maybe you should pop along to the next meeting, join, and point this out to them? Or do you expect to sit back and let organisations that you don’t belong to provide facilities for you? Any club is...

   Liked On: 27-06-2021, 11:56 PM

7. 
   Sh00ter liked post by 7x64 On thread : Best way to mount an optic on a shotgun rib

   Hi Viz made a three dot set of sights that mounted on dovetails/ replaced front bead. these work great, and as very lightweight no issues with mounting strength.

   Liked On: 16-05-2021, 08:25 PM

8. 
   Steve123 liked post by 7x64 On thread : Scope issues?

   If you can’t get hold of a bore sighter, a small mirror works too. Hold it up to the objective. I would centre the cross hairs - I.e. adjust so that you can only see one set of crosshairs. Once...

   Liked On: 08-02-2021, 09:26 AM

9. 
   MB liked post by 7x64 On thread : Garmin Instinct GPS watch

   Yup, had one about 8 months now. Mostly used to track exercise etc rather than for navigation, but it will work as such. Also use on the bike, skiing etc. Really enjoy mine but purely for hunting...

   Liked On: 27-12-2020, 05:40 PM

10. 
    Tangobravo liked post by 7x64 On thread : Needing - Butcher/ Processing

    Take it frozen to the butcher. Like Moa Hunter says you then need to keep it cold, which they will do. I had fresh meat and the butcher told me to just dice it into chunks and freeze before...

    Liked On: 27-12-2020, 02:49 PM

11. 
    Bent Barrel liked post by 7x64 On thread : Where do you carry your rangefinder?

    How are people toting their rangefinders? Haven’t found a happy solution yet, want it easy to get at but not snagging on stuff. I use a bino harness, but not a bino pack. I’m thinking of getting...

    Liked On: 20-12-2020, 01:49 PM

12. 
    dannyb liked post by 7x64 On thread : Needing - Butcher/ Processing

    Take it frozen to the butcher. Like Moa Hunter says you then need to keep it cold, which they will do. I had fresh meat and the butcher told me to just dice it into chunks and freeze before...

    Liked On: 19-12-2020, 01:12 PM

13. 
    dannyb liked post by 7x64 On thread : Needing - Butcher/ Processing

    You don’t need to mince it to get it made into sausage later - just freeze in pieces. The guy out at burnham is good for sausages etc. did some tahr for me earlier in the year and they turned out...

    Liked On: 18-12-2020, 07:56 PM

14. 
    hamsav liked post by 7x64 On thread : Stuck case removal tool Sth Taranaki?

    Stick it in the freezer for an hour and then try again in the press. The brass will shrink more than the steel so this often works too.

    Liked On: 17-12-2020, 11:33 AM

15. 
    Brian liked post by 7x64 On thread : Stuck case removal tool Sth Taranaki?

    Stick it in the freezer for an hour and then try again in the press. The brass will shrink more than the steel so this often works too.

    Liked On: 15-12-2020, 10:01 PM

Page 1 of 15 123456789101112131415 Last

• Jump to page: