akaroa1
Member

6777 Likes

Page 168 of 452 First ... 68118154155156157158159160161162163164165166167168169170171172173174175176177178179180181182218268 ... Last

• Jump to page:

1. 
   yeah_na_missed liked post by akaroa1 On thread : Hunting Permits

   I would like to eat a goat better than this wild lamb from last week ! So tender and tasty you could suck it through a straw So 234047

   Liked On: 24-09-2023, 11:57 AM

2. 
   -BW- liked post by akaroa1 On thread : Wildcat appreciation thread

   I tweaked the die length this morning to make the neck slightly longer This 9.5x62R case is remarkably similar to the 303 Brit Will feed and extract like a dream 228259

   Liked On: 23-09-2023, 04:21 PM

3. 
   Roarless20 liked post by akaroa1 On thread : Tips on reaming a chamber

   Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

   Liked On: 18-09-2023, 07:56 PM

4. 
   T.FOYE liked post by akaroa1 On thread : Cast Lead Thread ?

   And here's a good tip for bullet casters I mainly powder coat my bullets and use pass through sizers Haven't used my Lyman lube sizer in a few years So I made these dies bodies to take the...

   Liked On: 17-09-2023, 08:32 PM

5. 
   Moa Hunter liked post by akaroa1 On thread : Cast Lead Thread ?

   And here's a good tip for bullet casters I mainly powder coat my bullets and use pass through sizers Haven't used my Lyman lube sizer in a few years So I made these dies bodies to take the...

   Liked On: 16-09-2023, 12:57 AM

6. 
   Micky Duck liked post by akaroa1 On thread : Cast Lead Thread ?

   And here's a good tip for bullet casters I mainly powder coat my bullets and use pass through sizers Haven't used my Lyman lube sizer in a few years So I made these dies bodies to take the...

   Liked On: 15-09-2023, 10:11 PM

7. 
   Micky Duck liked post by akaroa1 On thread : Cast Lead Thread ?

   I've been doing a lot of casting and powder coating lately Belted Balls for the Dickson 233231 Three different flavour of bullets for the 32-20 233233

   Liked On: 15-09-2023, 09:30 PM

8. 
   Moa Hunter liked post by akaroa1 On thread : Cast Lead Thread ?

   I've been doing a lot of casting and powder coating lately Belted Balls for the Dickson 233231 Three different flavour of bullets for the 32-20 233233

   Liked On: 15-09-2023, 09:31 AM

9. 
   T.FOYE liked post by akaroa1 On thread : Cast Lead Thread ?

   Eastwood from Resto Supplies in Auckland

   Liked On: 15-09-2023, 07:15 AM

10. 
    kristopher liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 14-09-2023, 05:33 PM

11. 
    blip liked post by akaroa1 On thread : Tips on reaming a chamber

    I re cut a 223 Howa new old stock barrel a couple of weeks ago to 222 Rimmed The barrel was being stubbed into a Contender barrel shank and I was able to set it back a little I have cut quite a few...

    Liked On: 13-09-2023, 10:16 PM

12. 
    blip liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 13-09-2023, 10:15 PM

13. 
    Micky Duck liked post by akaroa1 On thread : Tips on reaming a chamber

    I re cut a 223 Howa new old stock barrel a couple of weeks ago to 222 Rimmed The barrel was being stubbed into a Contender barrel shank and I was able to set it back a little I have cut quite a few...

    Liked On: 13-09-2023, 08:47 PM

14. 
    Micky Duck liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 13-09-2023, 08:47 PM

15. 
    zimmer liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 13-09-2023, 08:41 PM

Page 168 of 452 First ... 68118154155156157158159160161162163164165166167168169170171172173174175176177178179180181182218268 ... Last

• Jump to page: