akaroa1
Member

6797 Likes

Page 248 of 454 First ... 148198234235236237238239240241242243244245246247248249250251252253254255256257258259260261262298348 ... Last

• Jump to page:

1. 
   RV1 liked post by akaroa1 On thread : Shooting rest in tussock country

   My technique is to have two walking poles Each pole has a number of turns of electrical tape around it 2/3rds of the way up Leave a small end section of tape folded back in itself so about 1cm does...

   Liked On: 24-10-2022, 09:36 PM

2. 
   Synthetic liked post by akaroa1 On thread : Shooting rest in tussock country

   My technique is to have two walking poles Each pole has a number of turns of electrical tape around it 2/3rds of the way up Leave a small end section of tape folded back in itself so about 1cm does...

   Liked On: 24-10-2022, 09:11 AM

3. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   No speed limit on powder coated gas checked bullets other than running out of case capacity

   Liked On: 20-10-2022, 08:17 AM

4. 
   Micky Duck liked post by akaroa1 On thread : Marlin Ballard restoration

   No hijacking

   Liked On: 19-10-2022, 06:47 PM

5. 
   Micky Duck liked post by akaroa1 On thread : Marlin Ballard restoration

   I usually cut my slots with the slitting saw in the milling machine Same thing different machine 208285

   Liked On: 19-10-2022, 06:46 PM

6. 
   Micky Duck liked post by akaroa1 On thread : Marlin Ballard restoration

   There's a small island of very nice checkering on the hammer cocking piece It would be a crime to fit a repop without the patina and these details So slow and steady and use as much of the...

   Liked On: 19-10-2022, 06:45 PM

7. 
   Micky Duck liked post by akaroa1 On thread : Marlin Ballard restoration

   That's pretty well what Mr Vulcan and I came up with in the weekend Now I need to sit down with my welding guru and see how he would approach it What's not so obvious it it's a surprisingly small...

   Liked On: 19-10-2022, 06:42 PM

8. 
   FRST liked post by akaroa1 On thread : Marlin Ballard restoration

   Then after finishing the woodwork deep clean and stock oil Re assembled it all Magnificent does not describe the butt stock walnut And my phone camera doesn't do it full justice It's such a dark...

   Liked On: 17-10-2022, 10:05 PM

9. 
   FRST liked post by akaroa1 On thread : Marlin Ballard restoration

   Then on to the much more enjoyable task of seeing that lovely piece of walnut hiding under nearly 150 years of dirt and oil 207938 It's pretty exciting to see walnut like that on a no.4...

   Liked On: 17-10-2022, 10:03 PM

10. 
    FRST liked post by akaroa1 On thread : Marlin Ballard restoration

    Well here I go again Just finally got my Marlin Ballard Perfection no.4 38-55 rifle Circa 1880 It's been a long search for a very rare rifle in NZ But to me this is the pick of the Marlin...

    Liked On: 17-10-2022, 10:02 PM

11. 
    Fssprecision liked post by akaroa1 On thread : Marlin Ballard restoration

    No hijacking

    Liked On: 17-10-2022, 06:26 PM

12. 
    Fssprecision liked post by akaroa1 On thread : Marlin Ballard restoration

    Hi hijacking at all I was just fishing for reasonable repair strategies from the more technically literate forum members

    Liked On: 17-10-2022, 06:26 PM

13. 
    Fssprecision liked post by akaroa1 On thread : Marlin Ballard restoration

    I usually cut my slots with the slitting saw in the milling machine Same thing different machine 208285

    Liked On: 17-10-2022, 05:01 PM

14. 
    Shamus_ liked post by akaroa1 On thread : Marlin Ballard restoration

    I usually cut my slots with the slitting saw in the milling machine Same thing different machine 208285

    Liked On: 17-10-2022, 04:37 PM

15. 
    Makros liked post by akaroa1 On thread : Marlin Ballard restoration

    I usually cut my slots with the slitting saw in the milling machine Same thing different machine 208285

    Liked On: 17-10-2022, 04:30 PM

Page 248 of 454 First ... 148198234235236237238239240241242243244245246247248249250251252253254255256257258259260261262298348 ... Last

• Jump to page: