akaroa1
Member

6806 Likes

Page 284 of 454 First ... 184234270271272273274275276277278279280281282283284285286287288289290291292293294295296297298334384 ... Last

• Jump to page:

1. 
   rambo-6mmrem liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 12-05-2022, 08:19 AM

2. 
   Noswal liked post by akaroa1 On thread : Blaser bolt head

   Yes all good LH bolts eject to the left RH bolts to the right

   Liked On: 11-05-2022, 11:35 PM

3. 
   DCN808T liked post by akaroa1 On thread : 1885 rustoration

   I got this very rough Winchester 1885 high wall action sent to me a few months ago. Someone had taken to it with a gas torch and vice grips while holding it in an engineers vice without jaw...

   Liked On: 11-05-2022, 10:50 PM

4. 
   Hutch liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 11-05-2022, 05:40 PM

5. 
   Skirch liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 10-05-2022, 02:14 PM

6. 
   Moa Hunter liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 10-05-2022, 01:39 PM

7. 
   Marty Henry liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 10-05-2022, 11:40 AM

8. 
   Mathias liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 10-05-2022, 11:12 AM

9. 
   Shamus_ liked post by akaroa1 On thread : 1885 rustoration

   Done 196558 196559 196560 196561

   Liked On: 10-05-2022, 11:05 AM

10. 
    PaulNZ liked post by akaroa1 On thread : 1885 rustoration

    Done 196558 196559 196560 196561

    Liked On: 10-05-2022, 10:58 AM

11. 
    Fssprecision liked post by akaroa1 On thread : 1885 rustoration

    Done 196558 196559 196560 196561

    Liked On: 10-05-2022, 09:55 AM

12. 
    300CALMAN liked post by akaroa1 On thread : 1885 rustoration

    Set up barrel again in the lathe Machine barrel shank and timing the octagonal flats and head space Then team chamber 45-70 196451 Turn it around and tidy up and lapp the muzzle 196452

    Liked On: 10-05-2022, 12:43 AM

13. 
    300CALMAN liked post by akaroa1 On thread : 1885 rustoration

    Then the real work began I made a bore guided drill on the Elliot tool and cutter grinder And drilled out the entire barrel to 16mm 196449 While it was in the lathe I took 3mm off the barrel...

    Liked On: 10-05-2022, 12:41 AM

14. 
    Fssprecision liked post by akaroa1 On thread : 1885 rustoration

    Thats a lot easier than doing it on the mill much easier to get lined up and better vision

    Liked On: 09-05-2022, 11:46 PM

15. 
    SixtyTen liked post by akaroa1 On thread : 1885 rustoration

    Then the real work began I made a bore guided drill on the Elliot tool and cutter grinder And drilled out the entire barrel to 16mm 196449 While it was in the lathe I took 3mm off the barrel...

    Liked On: 09-05-2022, 07:38 PM

Page 284 of 454 First ... 184234270271272273274275276277278279280281282283284285286287288289290291292293294295296297298334384 ... Last

• Jump to page: