akaroa1
Member

6817 Likes

Page 373 of 455 First ... 273323359360361362363364365366367368369370371372373374375376377378379380381382383384385386387423 ... Last

• Jump to page:

1. 
   hotbarrels liked post by akaroa1 On thread : What little pesties did you bowl over today?

   There were 2 hares sitting on my rifle range this morning around the 50m mark. I snuck in and pulled out the rifle at the front of the safe and shot one off hand with a clean middle chest shot. ...

   Liked On: 02-03-2020, 04:23 PM

2. 
   Steelisreal liked post by akaroa1 On thread : What little pesties did you bowl over today?

   There were 2 hares sitting on my rifle range this morning around the 50m mark. I snuck in and pulled out the rifle at the front of the safe and shot one off hand with a clean middle chest shot. ...

   Liked On: 02-03-2020, 02:30 PM

3. 
   norsk liked post by akaroa1 On thread : 500 BPE load advice

   I turned a couple of basic sizing dies this evening One is a straight die that sizes about 10mm of the neck just enough to hold the projectiles The other die is exact case taper and just smooths...

   Liked On: 02-03-2020, 05:34 AM

4. 
   takbok liked post by akaroa1 On thread : 500 BPE load advice

   I have just finished turning a depriming punch for the 500 cases Tapered to the internal dimension. Will harden and temper both ends and it should work just fine 130969130970

   Liked On: 02-03-2020, 03:53 AM

5. 
   Maca49 liked post by akaroa1 On thread : 500 BPE load advice

   I turned a couple of basic sizing dies this evening One is a straight die that sizes about 10mm of the neck just enough to hold the projectiles The other die is exact case taper and just smooths...

   Liked On: 01-03-2020, 09:30 PM

6. 
   Micky Duck liked post by akaroa1 On thread : 500 BPE load advice

   norsk I just put the first card wad in to let me compress the powder down a little with a 1/2" drift punch And the top card was just because I was having some fun. Yes I know I could rip into...

   Liked On: 01-03-2020, 08:16 PM

7. 
   john m liked post by akaroa1 On thread : 500 BPE load advice

   Thanks John That's a whole can of worms to open up ! A book like that could get me in a lot of very expensive trouble

   Liked On: 28-02-2020, 08:49 AM

8. 
   Moa Hunter liked post by akaroa1 On thread : 500 BPE load advice

   131208

   Liked On: 28-02-2020, 08:34 AM

9. 
   csmiffy liked post by akaroa1 On thread : 1885 rustoration

   homebrew.357 no stress at this end I made two complete spring sets for 1885s copying my original low wall ones. A mate friend and hardened and tempered them. Both sets work perfectly So now...

   Liked On: 26-02-2020, 09:30 AM

10. 
    Moa Hunter liked post by akaroa1 On thread : Pump rifle build questions - 375 h&h??

    LoganRobertson it sounds like you need a double rifle Two quick accurate shots Go as big on caliber as you like Easy to feed No bolt Short Probably cheaper in the long ran compared to...

    Liked On: 26-02-2020, 08:43 AM

11. 
    Maca49 liked post by akaroa1 On thread : 500 BPE load advice

    Well I have just fired the Hollis Martini Set up with sand bags and a string on the trigger It went bang like I had expected Primer was fine Still sitting where I put it so not to much recoil...

    Liked On: 25-02-2020, 09:06 PM

12. 
    Micky Duck liked post by akaroa1 On thread : 500 BPE load advice

    norsk I'm just delighted it went bang and stayed in one piece I know heaps more about its chamber now and its sizes So I can google around and find out more about the type of projectile that most...

    Liked On: 25-02-2020, 07:54 PM

13. 
    Micky Duck liked post by akaroa1 On thread : 500 BPE load advice

    I have just finished turning a depriming punch for the 500 cases Tapered to the internal dimension. Will harden and temper both ends and it should work just fine 130969130970

    Liked On: 25-02-2020, 07:46 PM

14. 
    Micky Duck liked post by akaroa1 On thread : 500 BPE load advice

    Advice wanted from anyone actually using a 500 BPE or 500/450 BPE or experienced with something similar like a 50-120 or 50-140 Sharps ? Or knows someone reliable who has the same and shoots it...

    Liked On: 25-02-2020, 07:45 PM

15. 
    stevodog liked post by akaroa1 On thread : 18 inch 308 powder

    Winchester 748 and magnum primers Should get 125s into the low to mid 2900s

    Liked On: 24-02-2020, 01:16 PM

Page 373 of 455 First ... 273323359360361362363364365366367368369370371372373374375376377378379380381382383384385386387423 ... Last

• Jump to page: