astridhunterchch
Member

28 Likes

Page 2 of 2 First 12

• Jump to page:

1. 
   astridhunterchch liked post by 7mmwsm On thread : Primer Shortage...to be continued???

   Flintlock is the future.

   Liked On: 31-08-2023, 01:19 PM

2. 
   astridhunterchch liked post by Mathias On thread : Ruger 10/22 wont cycle

   The answer is in your cocking handle spring. I bought a Kidd kit with 3 different weight springs to solve the very same problem. Also the Volquatsen exact edge extractor can help too. I wouldn't like...

   Liked On: 27-08-2023, 08:32 PM

3. 
   astridhunterchch liked post by norsk On thread : Reloading 6.5x55

   It depends on what you are after? As a "bang flop" cartridge I think a 308 has the edge,for flat shooting and mild recoil/little blast the old Swede is hard to beat. I have a couple and have had a...

   Liked On: 14-08-2023, 05:33 AM

4. 
   astridhunterchch liked post by 7mmwsm On thread : Crimping ACTIV 20 Gauge Hulls

   Possibly trying to crimp them to short. And creating to much internal pressure. Try adjusting the crimping station out a bit. Or find some shorter wads. Some pictures of the problem would help.

   Liked On: 13-08-2023, 10:41 AM

5. 
   astridhunterchch liked post by nor-west On thread : 6.5 x 55 Arch Improved Load Data

   I can give you some loads I ran in a 6.5x57 AI if it helps.

   Liked On: 13-08-2023, 08:44 AM

6. 
   astridhunterchch liked post by HUNTY On thread : 6.5 x 55 Arch Improved Load Data

   I am using N560 in my 6.5x55 AI, May be a bit hard to find some at the moment though.

   Liked On: 13-08-2023, 08:43 AM

7. 
   astridhunterchch liked post by Moa Hunter On thread : 6.5 x 55 Arch Improved Load Data

   My thoughts would be to use something slower than 4350 / 2209, perhaps even superformance. The general rule of thumb with improved cartridges is to use a load near to max for the standard round as...

   Liked On: 13-08-2023, 08:43 AM

8. 
   astridhunterchch liked post by zimmer On thread : 6.5 x 55 Arch Improved Load Data

   This seems to be from Ackley's book. I'll dig out my copies later. 230986

   Liked On: 13-08-2023, 08:43 AM

9. 
   astridhunterchch liked post by grandpamac On thread : 6.5 x 55 Arch Improved Load Data

   Depending on the projectile weight you are using IMR4350 and IMR4831 should work well if you can get any. I would not trust any old data as the pressures may be stratospheric. Data for the parent...

   Liked On: 13-08-2023, 08:43 AM

10. 
    astridhunterchch liked post by Longrun On thread : 6.5 x 55 Arch Improved Load Data

    I use w760 in std swede. On current availability I'd use staball 6.5.

    Liked On: 13-08-2023, 08:43 AM

11. 
    astridhunterchch liked post by zimmer On thread : 6.5 x 55 Arch Improved Load Data

    I've got some of his books. I'll have a look. Old data may not be your best solution though as some of the older powders have had their recipes changed over the years, maybe only slightly though. In...

    Liked On: 13-08-2023, 08:43 AM

12. 
    astridhunterchch liked post by dannyb On thread : 6.5 x 55 Arch Improved Load Data

    if you can find some Hodgdon H4350 that is ADI2209 repackaged for the american market....good luck :(

    Liked On: 13-08-2023, 08:43 AM

13. 
    astridhunterchch liked post by Micky Duck On thread : 6.5 x 55 Arch Improved Load Data

    what powder are you thinking....is far better way to find data...

    Liked On: 13-08-2023, 08:43 AM

Page 2 of 2 First 12

• Jump to page: