BenTheBuilder
Member

51 Likes

Page 2 of 4 First 1234 Last

• Jump to page:

1. 
   BenTheBuilder liked post by dannyb On thread : North Canterbury Rifle range

   Whilst i have access to a range on private land it's not mine and not my place to invite others unfortunately. Sorry

   Liked On: 24-08-2023, 02:41 PM

2. 
   BenTheBuilder liked post by Micky Duck On thread : North Canterbury Rifle range

   Moa Hunter dannyb

   Liked On: 24-08-2023, 09:31 AM

3. 
   BenTheBuilder liked post by Snoppernator On thread : Bush Huntng Pack Mod

   So here's an option if you have a fantastic backpack and are looking to convert it to a bush hunting. Rusky sensibly inspired me to look at getting a decent pack after my pikau just fell apart under...

   Liked On: 20-08-2023, 09:03 AM

4. 
   BenTheBuilder liked post by Kiwi Greg On thread : Small Rifle Primers

   Believe it or not IIRC I do have some fired & unfired 7WSM Winchester brass at work, Along with even more scarce Remington 300 Rum brass & factory ammo as well as 7 Saum RP brass and ammo,...

   Liked On: 19-08-2023, 05:48 PM

5. 
   BenTheBuilder liked post by gqhoon On thread : FL resized rounds wont chamber

   Ben, find brass that meets the criteria below 1 - Factory round, pull the projectile and dump powder, confirm it fits in your chamber 2- case fired in your chamber, sized and fits back in your...

   Liked On: 14-08-2023, 12:58 PM

6. 
   BenTheBuilder liked post by grandpamac On thread : FL resized rounds wont chamber

   Greetings again BenTheBuilder, Although frustrating at the time the difficulties you are having will teach you much. So to summarise: 1, Factory ammo chambers. 2, Some of your once fired brass...

   Liked On: 14-08-2023, 12:57 PM

7. 
   BenTheBuilder liked post by Micky Duck On thread : FL resized rounds wont chamber

   so...in laymans terms....your squishing the case back to within spec...BUT the shoulder area SEEMS to be a bit rounded making it slightly over length.... and you cant get rifle bolt to cam over and...

   Liked On: 13-08-2023, 10:04 PM

8. 
   BenTheBuilder liked post by johnd On thread : FL resized rounds wont chamber

   Skip read to here so probably missed afew details. Of the two cases mentioned in this (above) why is one shorter than the other and why can't you make the longer one the same as the shorter one?...

   Liked On: 13-08-2023, 08:57 PM

9. 
   BenTheBuilder liked post by zimmer On thread : FL resized rounds wont chamber

   I'll ask the question again. Can you corfirm that the case in pic one definitely fits and pic 3 doesn't? If you have a case that fits a few measurements will tell you what the problem ig. eg an...

   Liked On: 13-08-2023, 08:29 PM

10. 
    BenTheBuilder liked post by Micky Duck On thread : Case lengthening when bump sizing

    bumped it for our man having issues with the WSM

    Liked On: 13-08-2023, 08:24 PM

11. 
    BenTheBuilder liked post by Micky Duck On thread : tight closing the bolt

    bump

    Liked On: 13-08-2023, 07:52 PM

12. 
    BenTheBuilder liked post by chunkyboi On thread : tight closing the bolt

    Interesting thoughts of yours re: the concept of the decapping ball pulling the shoulder on the up-stroke, I was having this problem with 1/10 rounds with .270WSM using Lee dies, and thought I must...

    Liked On: 13-08-2023, 07:38 PM

13. 
    BenTheBuilder liked post by ElDax On thread : FL resized rounds wont chamber

    When using the lee lube you need to lube the inside of the neck also just in case you aren't doing that, I use a cotton swab to give them all a dose while sitting in the case holder.

    Liked On: 12-08-2023, 10:15 PM

14. 
    BenTheBuilder liked post by mikee On thread : FL resized rounds wont chamber

    Perhaps there is a forum member/experienced reloader locally to you who may be able to visit and see it they can assist solving your issue? Most times "in-person" is much better than trying to...

    Liked On: 12-08-2023, 10:15 PM

15. 
    BenTheBuilder liked post by Micky Duck On thread : FL resized rounds wont chamber

    I searched for and rebumped the last two relevant threads on this type of issue for you...

    Liked On: 12-08-2023, 08:57 PM

Page 2 of 4 First 1234 Last

• Jump to page: