Bill999
Member

1851 Likes

Page 77 of 124 First ... 276364656667686970717273747576777879808182838485868788899091 ... Last

• Jump to page:

1. 
   outlander liked post by Bill999 On thread : NZ Post up to frks, 2 month delay and told me that they won't deliver to WLG

   dont you feel safer tho?

   Liked On: 06-11-2019, 02:51 PM

2. 
   lee308 liked post by Bill999 On thread : NZ Post up to frks, 2 month delay and told me that they won't deliver to WLG

   dont you feel safer tho?

   Liked On: 06-11-2019, 02:02 PM

3. 
   ChrisW liked post by Bill999 On thread : How to get fast twist barrels in NZ

   You and Dean Maisy share the same opinion, I have a suppressed 308 already and just want something smaller and lighter with less case capacity for hopefully less noise my 308 runs Roberts 151gr...

   Liked On: 06-11-2019, 08:31 AM

4. 
   sixtus liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

   putting it muzzle forward would be asking even harder for baffle strike unless you cut it down and done a muzzle forward on like a 4 inch barrel a series of washers that are 12 ga on the outside...

   Liked On: 04-11-2019, 03:50 PM

5. 
   sixtus liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

   Be a cool idea to use the rest of the 12ga hole as a suppressor if you could ensure insert and baffle alignment

   Liked On: 04-11-2019, 03:30 PM

6. 
   Cordite liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

   Be a cool idea to use the rest of the 12ga hole as a suppressor if you could ensure insert and baffle alignment

   Liked On: 04-11-2019, 10:17 AM

7. 
   canross liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

   Be a cool idea to use the rest of the 12ga hole as a suppressor if you could ensure insert and baffle alignment

   Liked On: 04-11-2019, 09:26 AM

8. 
   Tommy liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

   Be a cool idea to use the rest of the 12ga hole as a suppressor if you could ensure insert and baffle alignment

   Liked On: 02-11-2019, 09:28 PM

9. 
   mimms2 liked post by Bill999 On thread : Brno 601 what now

   I would give it a good clean, make sure the action and bottom metal are correctly mated and check for wear spots where metal on metal and address anything too proud or bed anything also it may...

   Liked On: 01-11-2019, 08:22 PM

10. 
    Tuckerbox liked post by Bill999 On thread : Brno 601 what now

    I would give it a good clean, make sure the action and bottom metal are correctly mated and check for wear spots where metal on metal and address anything too proud or bed anything also it may...

    Liked On: 01-11-2019, 06:56 PM

11. 
    Tahr liked post by Bill999 On thread : Brno 601 what now

    I would give it a good clean, make sure the action and bottom metal are correctly mated and check for wear spots where metal on metal and address anything too proud or bed anything also it may...

    Liked On: 01-11-2019, 01:21 PM

12. 
    Moa Hunter liked post by Bill999 On thread : Brno 601 what now

    I would give it a good clean, make sure the action and bottom metal are correctly mated and check for wear spots where metal on metal and address anything too proud or bed anything also it may...

    Liked On: 01-11-2019, 11:43 AM

13. 
    Moa Hunter liked post by Bill999 On thread : Brno 601 what now

    this happened to my brno too the firieing pin had gunk in it and had mushroomed off too much and wasnt setting off harder primers

    Liked On: 01-11-2019, 11:42 AM

14. 
    WillB liked post by Bill999 On thread : How to get fast twist barrels in NZ

    Im after a pair of barrels one in 338 cal and one in 30 cal the trick is I want absurdly fast twist rates (1-5 for the 30 and 1-3 for the 338) or basically as fast as possible as I can get my...

    Liked On: 01-11-2019, 11:06 AM

15. 
    canross liked post by Bill999 On thread : Full barrel suppressor vs partial overbarrel/end forward

    It becomes a look thing at a certain point the smaller diameter has to be longer to get the same internal volume aparently one inch forward is equal to 5 inches behind the muzzle so weight wise...

    Liked On: 10-10-2019, 08:41 AM

Page 77 of 124 First ... 276364656667686970717273747576777879808182838485868788899091 ... Last

• Jump to page: