bing
Member

157 Likes

Page 2 of 11 First 1234567891011 Last

• Jump to page:

1. 
   bing liked post by MSL On thread : The dogs nuts

   I say no, seeing as you’ve not made any mention of any reason why you would Sent from my iPhone using Tapatalk

   Liked On: 15-01-2022, 10:22 AM

2. 
   bing liked post by ONYVA On thread : The dogs nuts

   google it and read as much as you can, currant opinion is no.

   Liked On: 15-01-2022, 10:22 AM

3. 
   bing liked post by Tentman On thread : 6x45 Rem barrel

   Interesting. The 6mm-204 would seem to be the best bet in a "medium" action with a .378 boltface. I think the key is to get something that will run at 30gns powder or a tiny bit under - with...

   Liked On: 31-12-2021, 11:28 PM

4. 
   bing liked post by oraki On thread : First Helicopter Company pulls The Pin On The Tahr Cull

   Comments on some pages were way out of line. Talks of bringing down choppers etc. That would be what they’re referring to. The writers were quickly bought back into line, but bullshit comments like...

   Liked On: 23-07-2020, 10:29 PM

5. 
   bing liked post by Orcrist On thread : Bird Predator Control

   142951142950

   Liked On: 21-06-2020, 09:17 PM

6. 
   bing liked post by Wingman On thread : 6x45 Rem barrel

   I finally received what was supposed to be a pre-chambered 22" long fluted S/S 6mm TCU barrel but it wasnt. I had to make a chamber cast to actually work out what it was. Someone had used a .223...

   Liked On: 31-05-2020, 10:58 PM

7. 
   bing liked post by akaroa1 On thread : Self isolation gun projects

   Another double rifle day Turned some barrels in the wood lathe to try and sort profiles and start on the ribs while the barrels are being made. Also a good template for the barrel makers copy lathe...

   Liked On: 12-05-2020, 08:24 PM

8. 
   bing liked post by akaroa1 On thread : Self isolation gun projects

   What's everyone doing for self isolation projects I have a few years worth of gun projects on the book But i suspect I might rip through them this winter Fitted and tested a 209 primer...

   Liked On: 12-05-2020, 07:18 PM

9. 
   bing liked post by gundoc On thread : Making a Rolling block rifle on my lathe.

   You will have to grind up a piece of HSS to the Acme thread shape (taking the dimensions off your top slide screw) making sure the depth of the tool will allow enough depth of cut. Make sure the...

   Liked On: 03-05-2020, 02:26 PM

10. 
    bing liked post by rambo-6mmrem On thread : Glass bedding pros and cons

    Always worth bedding the only con is the slight waight increase from the glass which is very little Ive never seen a rifle get worse from a bedding job only improvement Ive seen already very...

    Liked On: 03-05-2020, 04:13 AM

11. 
    bing liked post by akaroa1 On thread : Making a Rolling block rifle on my lathe.

    It's only 2200 kg Certainly not going anywhere fast It can make swarf at an astonishing rate

    Liked On: 28-04-2020, 05:48 PM

12. 
    bing liked post by akaroa1 On thread : Making a Rolling block rifle on my lathe.

    I did some serious stock reduction today to knock a 32mm diameter round bar into a 15mm square bar. Relatively easy with the power feed. I was able to run the mill in the feed and be working on the...

    Liked On: 28-04-2020, 03:53 PM

13. 
    bing liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    I don`t know if I will build all the extra bits, have to see how hard it is or how lazy I am. The round bit is 3.900"dia, and yes I have fly cut a flat on one side, it was going to be the action for...

    Liked On: 28-04-2020, 03:50 PM

14. 
    bing liked post by akaroa1 On thread : Making a Rolling block rifle on my lathe.

    There is no dignity in haste !

    Liked On: 28-04-2020, 03:47 PM

15. 
    bing liked post by Cigar On thread : Short deer/pig/goat rifles for the tight stuff (lets see em)

    My two shorties - a Winchester Model 94 Trapper 30-30, 16 inch barrel, OAL about 860mm, bought new in 1986, and Bergara 308 takedown, 16.5 inch barrel, OAL 800mm, 900mm with DPT mini-centrefire,...

    Liked On: 26-04-2020, 04:47 PM

Page 2 of 11 First 1234567891011 Last

• Jump to page: