Boxton
Member

405 Likes

Page 13 of 27 First 123456789101112131415161718192021222324252627 Last

• Jump to page:

1. 
   Boxton liked post by akaroa1 On thread : 577 Super Snider build and chamber reamer size

   My Snider dies set fits in a standard 7/8" reloading press The sizer on left screws in from below and stops at the small bottom shoulder Works well Plus neck flaring die Seating die and case...

   Liked On: 29-07-2022, 10:02 AM

2. 
   Boxton liked post by Tedz50 On thread : 577 Super Snider build and chamber reamer size

   Boxton My RCBS press has a removable bushing to use snider and M-henry dies but was too short for 50 BMG so have Lee 50BMG press also if you wish to use them.

   Liked On: 29-07-2022, 09:18 AM

3. 
   Boxton liked post by akaroa1 On thread : 577 Super Snider build and chamber reamer size

   I got very lucky on those dies Was a bit worried they would struggle to form the magtech to snider But it was very easy with the annealing done properly Some time soon I need to set up the...

   Liked On: 27-07-2022, 09:30 PM

4. 
   Boxton liked post by csmiffy On thread : 17 Hornet

   Not a 17 hornet but a bloody nice 22 hornet Damascus double rifle by Bradshaw rifle and gun Damascus pattern by case hardening I believe 202368

   Liked On: 26-07-2022, 10:15 PM

5. 
   Boxton liked post by SL600 On thread : 17 Hornet

   202084

   Liked On: 24-07-2022, 11:29 PM

6. 
   Boxton liked post by SL600 On thread : 17 Hornet

   Yes I have 17 Hornet in HW66 Waihrauch. It likes 20Grain Vmax best. Great groups even from factory Hornady amo. Half inch groups @100m easily achieved with home loads. Wasted so much time working...

   Liked On: 22-07-2022, 07:59 PM

7. 
   Boxton liked post by Fssprecision On thread : Quick tidy up of a Snider today

   A chap just picked this up complete with the ultra rare rod…I gave it a strip down and gentle tidy up…came out great I think and still good enough to shoot. I need to work out how to copy the rod...

   Liked On: 08-05-2022, 11:03 PM

8. 
   Boxton liked post by southernman On thread : 7mm rem mag reloading cost

   Depending on component between $2-3, 15-20 c for primer, powder 75-99 cents. Brass reused from factory , Bullets are you biggest cost. Premium $2-3, soft point. .75-1.25 I recommend a good old...

   Liked On: 04-05-2022, 12:17 AM

9. 
   Boxton liked post by Woody On thread : GWP Owners

   Just keep clipping the surplus as nescesarry. You dont need to be heavy handed about it, just a little as required.194213

   Liked On: 10-04-2022, 05:33 PM

10. 
    Boxton liked post by wekaman On thread : Douglas River Hunting

    Don't listen to anyone who tells you the "low route" out the Douglas to Cassels flat is an option. As said, the track up from Horace Walker hut to Terraces on true right of Douglas and onwards will...

    Liked On: 24-03-2022, 02:25 AM

11. 
    Boxton liked post by scottrods On thread : New to Canterbury

    once Covid red traffic light goes, come along to the local NZDa branch meetings and get involved in branch hunts. Heaps of deer in lake Sumner RHA area.

    Liked On: 05-03-2022, 06:12 PM

12. 
    Boxton liked post by Von Gruff Knives On thread : Various Knives

    The new Tahr Hunter design. The specs for the first commission were to have a FF grind on the .156 1095 blade and an inch of jimpinh.with otrange G10 liners under the scolloped OD canvas micarta...

    Liked On: 09-02-2022, 09:51 PM

13. 
    Boxton liked post by Gun nut On thread : Lee Enfields and the 30-40 Krag.

    Behold, my stuff! 189675

    Liked On: 08-02-2022, 08:11 PM

14. 
    Boxton liked post by misser On thread : Hand Priming Tool

    rcbs will likely replace it

    Liked On: 30-01-2022, 07:51 PM

15. 
    Boxton liked post by chainsaw On thread : On the wall at last

    Big 14 from a couple of years back, been safely boxed up from taxidermist for last 12 months waiting for his chance to get to Taupo and go up on the walk. In rating the beast was a blast, I’d...

    Liked On: 29-01-2022, 07:57 PM

Page 13 of 27 First 123456789101112131415161718192021222324252627 Last

• Jump to page: