buzzmann
Member

326 Likes

Page 6 of 22 First 1234567891011121314151617181920 ... Last

• Jump to page:

1. 
   buzzmann liked post by wsm junkie On thread : Sako lovers

   :cave:

   Liked On: 10-01-2025, 07:08 PM

2. 
   buzzmann liked post by Jaco Goosen On thread : Model 7 thread size

   Hey Buzz. I would have gone down 1 size. The shoulder for the silencer is really important.

   Liked On: 09-01-2025, 05:16 PM

3. 
   buzzmann liked post by 7mmsaum On thread : sako 90 finnlight

   The peak are works of art Using a 308 and they’re robust with decent rings and a matching scope 266612

   Liked On: 09-01-2025, 05:15 PM

4. 
   buzzmann liked post by 6x47 On thread : Model 7 thread size

   I'd say the orig owner had that can sitting around or got it cheap- it was then "made to fit" the pencil barrel.

   Liked On: 08-01-2025, 07:42 PM

5. 
   buzzmann liked post by 6x47 On thread : Model 7 thread size

   Realise that. Yeh, it was hardly a gunsmith's recommendation..

   Liked On: 08-01-2025, 07:42 PM

6. 
   buzzmann liked post by Fssprecision On thread : Model 7 thread size

   Threads for suppressors should have a minimum shoulder of 0.50mm (so needs to be 15mm diameter behind the thread) to secure to. Doesn’t look like that has one at all.

   Liked On: 08-01-2025, 01:38 PM

7. 
   buzzmann liked post by scotty On thread : Model 7 thread size

   just thinking ...... maybe vernier the od of the barrel and the thread .......if the same maybe its a bubba job not done on a lathe and may not be true to the bore which would/could lead to bullet...

   Liked On: 08-01-2025, 09:41 AM

8. 
   buzzmann liked post by scotty On thread : Model 7 thread size

   run a die nut over it with vivid on the face to see if its contacting what there is of a shoulder? the thread looks like its taken a few knocks anyway

   Liked On: 08-01-2025, 09:33 AM

9. 
   buzzmann liked post by chainsaw On thread : Model 7 thread size

   Most M7 barrels I’ve come across the factory bbl is threaded 1/2x28 or 1/2x20

   Liked On: 08-01-2025, 08:11 AM

10. 
    buzzmann liked post by matto1234 On thread : Model 7 thread size

    I dont feel like unwrapping my dpt to have a look but i think it should still pull up internally?

    Liked On: 08-01-2025, 08:04 AM

11. 
    buzzmann liked post by Tahr On thread : REM model 7 load

    I used it with 120 NBT. 3K with 18" Worked well.

    Liked On: 07-01-2025, 02:08 PM

12. 
    buzzmann liked post by No.3 On thread : REM model 7 load

    Tried it when setting up the load I mentioned above, very slightly slower start load for start load compared to 2208 and showed pressure signs earlier than we expected in that combo (140gr pill). ...

    Liked On: 07-01-2025, 08:52 AM

13. 
    buzzmann liked post by chainsaw On thread : REM model 7 load

    Above should read 2208, not 2207 and are running the 119gn Hammers at 3000fps

    Liked On: 06-01-2025, 07:47 PM

14. 
    buzzmann liked post by Mick Hunter On thread : REM model 7 load

    43 grains 2208 139 Hornady soft point. Model 7, 2650 fps

    Liked On: 06-01-2025, 07:29 PM

15. 
    buzzmann liked post by chainsaw On thread : REM model 7 load

    150 ELDX or 120 NBTs on top of 2208/Varget. I’m currently playing with some 119gn Hammers in 18in bbl 708 with 2207. But it’s a Mk5 Weatherby.

    Liked On: 06-01-2025, 07:28 PM

Page 6 of 22 First 1234567891011121314151617181920 ... Last

• Jump to page: