CBH Australia
Member

997 Likes

Page 60 of 67 First ... 1046474849505152535455565758596061626364656667 Last

• Jump to page:

1. 
   CBH Australia liked post by Jaco Goosen On thread : New Aussie to the forum

   Welcome Chris. You'll enjoy hunting NZ. Some nice african animals there. Wish I spent more time hunting Kudu. Hunted lots of Warthog and I have to be honest - I love hunting warthogs.

   Liked On: 03-11-2021, 11:44 AM

2. 
   CBH Australia liked post by PadLo On thread : New Aussie to the forum

   Welcome mate. You'll love hunting in NZ.

   Liked On: 03-11-2021, 12:02 AM

3. 
   CBH Australia liked post by Micky Duck On thread : New Aussie to the forum

   that right there is PERFECT attitude...go for walk to check out the country,any animal is a bonus and the trip is a success BEFORE you start. welcome aboard.......we have plenty of Aussie...

   Liked On: 03-11-2021, 12:02 AM

4. 
   CBH Australia liked post by NzMavrick On thread : New Aussie to the forum

   Welcome! hope you enjoy your stay!

   Liked On: 03-11-2021, 12:02 AM

5. 
   CBH Australia liked post by High Country Boy On thread : aerial culling still happening

   If they were after tahr that are outside the feral range. They will be culling and shooting everything

   Liked On: 12-10-2021, 12:16 AM

6. 
   CBH Australia liked post by RUMPY On thread : aerial culling still happening

   A330driver I was out with Micky duck yesterday. Firstly it was hard to get definite rego of chopper and the ute was a genuine DoC hilux so no, this activity wasn't illegal in our opinion. I just find...

   Liked On: 12-10-2021, 12:16 AM

7. 
   CBH Australia liked post by winaa On thread : Model 7 7mm08 150gn eldx load development

   Use 154gr ADI data for the 150 ELD-X. That's how Hornady groups them in their reloading manual. 2208 is the best burn rate for a 7mm08 with a barrel longer than 16 inches, if you can get it.

   Liked On: 10-10-2021, 12:07 AM

8. 
   CBH Australia liked post by GWH On thread : Model 7 7mm08 150gn eldx load development

   Yeah if it holds enough velocity and energy and precision out to 450-500 you should be fine should the need be there one day. With my 15" 708 pushing 140 nbts at 2720 fps it holds in excess of...

   Liked On: 10-10-2021, 12:05 AM

9. 
   CBH Australia liked post by dannyb On thread : Model 7 7mm08 150gn eldx load development

   Granted pretty much any soft point would do the buisness and whilst this rifle is predominantly 0-300ish yard rifle I'd love to have the confidence to stretch it further should the situation...

   Liked On: 10-10-2021, 12:04 AM

10. 
    CBH Australia liked post by 25 /08 IMP On thread : Model 7 7mm08 150gn eldx load development

    Hi Danny I'm using Laupa brass in the 7-08 I'm working a load for at the moment. I'm using 2308 and 150 ELDX from a 20" Tikka seated to mag length. I did a ladder last night and went up to 40.6...

    Liked On: 10-10-2021, 12:03 AM

11. 
    CBH Australia liked post by keengunNic On thread : Model 7 7mm08 150gn eldx load development

    Ive personally had rubbish experience with federal brass, as you mentioned sloppy primer pockets varying throughout the same lot of brass. Made the switch to starline in 7mm08 and have had awesome...

    Liked On: 10-10-2021, 12:02 AM

12. 
    CBH Australia liked post by Hunty1 On thread : Model 7 7mm08 150gn eldx load development

    My personal experience with 7mm08 lapua was it was far less capacity than other cases. I couldn't get to max book loads without stamping. Not a bad thing though same preasure for less powder!

    Liked On: 10-10-2021, 12:02 AM

13. 
    CBH Australia liked post by dannyb On thread : Model 7 7mm08 150gn eldx load development

    Very fair call.....Sometimes a reality check is what's needed....I do love to tinker, sometimes to my detriment. There is nothing wrong with the 2209 groups thats for sure I guess it was just too...

    Liked On: 10-10-2021, 12:00 AM

14. 
    CBH Australia liked post by grandpamac On thread : Model 7 7mm08 150gn eldx load development

    Greetings dannyb, First and most important no it is not safe to use .308W data for the 7mm-08. Pressure will be much higher. I did a quick check on data for AR2206H 40.5 grains with 150 grain HPBT....

    Liked On: 10-10-2021, 12:00 AM

15. 
    CBH Australia liked post by dannyb On thread : Model 7 7mm08 150gn eldx load development

    So an interesting quandary has arisen......:o It has been suggested that in the short barrel I may see better velocity with ADI2206h, I have access to about half a bottle but there is no load data...

    Liked On: 09-10-2021, 11:58 PM

Page 60 of 67 First ... 1046474849505152535455565758596061626364656667 Last

• Jump to page: