chainsaw
Member

4159 Likes

Page 85 of 278 First ... 357172737475767778798081828384858687888990919293949596979899135185 ... Last

• Jump to page:

1. 
   chainsaw liked post by Brian On thread : Rifle Bedding Opinions

   I'd try a washer on the top of that rear pillar to get it touching first.

   Liked On: 15-05-2022, 01:46 PM

2. 
   chainsaw liked post by stagstalker On thread : Rifle Bedding Opinions

   55 and 65 inch pounds seems like a lot. I could be wrong but on my plastic Tikka stocks I torque to 35 inch pounds to avoid any unnecessary compression and on my carbon stocks with pillars I go 40...

   Liked On: 15-05-2022, 01:46 PM

3. 
   chainsaw liked post by stug On thread : Rifle Bedding Opinions

   When I bed my Rem 700 I put a single layer of insulation tape around the action so only the rear tang and front of the action are touching and are bedded. The rest of the action is essentially free...

   Liked On: 15-05-2022, 01:46 PM

4. 
   chainsaw liked post by stug On thread : Rifle Bedding Opinions

   A friends Bergara had the groups tighten right up when he decreased the torque on the screws. You could try loosening them a bit more and see what happens. I wouldn’t lower the action any unless you...

   Liked On: 15-05-2022, 10:41 AM

5. 
   chainsaw liked post by Kelton On thread : REM700 bolt and bolt face

   As far as I no the bolt body diameter is the same so it should be no dramas

   Liked On: 15-05-2022, 10:16 AM

6. 
   chainsaw liked post by stug On thread : REM700 bolt and bolt face

   Yep I had my 30/06 opened up to 7mm mag. You will probably need to replace the extractor with a sako style too though.

   Liked On: 15-05-2022, 10:16 AM

7. 
   chainsaw liked post by viper On thread : Show me your knives

   196767 A Viper in 1084. Stabilized Pohutakawa with dual layer micarta . G10 liners and pins. For a Tasmanian hunter in NZ on some guided hunts wanting to take a knife with some NZ timber in it to...

   Liked On: 13-05-2022, 04:54 PM

8. 
   chainsaw liked post by rugerman On thread : Dalmatian training

   No matter how hard you try you wont be able to get them to change their spots. mmm interesting, just had a good look at their website, looks pretty dodgy. In the "about Us" section there is no...

   Liked On: 12-05-2022, 08:52 PM

9. 
   chainsaw liked post by XR500 On thread : Home invasion

   Listening to the guidance the judge gave the jury before they retired I am fairly sure he was gunning for a Not Guilty verdict too. Its all nice and rational to pick to pieces a situation like...

   Liked On: 12-05-2022, 08:49 PM

10. 
    chainsaw liked post by stug On thread : 7mm rem velocity

    71-72gr 2217 with a 162gr projectile is a pretty common load. 67 with a 154 is a light load. You should be getting close to 3100fps with a 154 in a 24” barrel.

    Liked On: 12-05-2022, 08:42 PM

11. 
    chainsaw liked post by hotsoup On thread : Stags & Bucks 2022

    228DS, Greenstone 196716

    Liked On: 12-05-2022, 01:51 PM

12. 
    chainsaw liked post by vulcannz On thread : Pogo on National radio

    I heard her on NZtalk with Heather, she was claiming 'going soft on crime' is sexist (or misogynistic), Heather couldn't get her to answer how exactly that's sexist other than implying any criticism...

    Liked On: 10-05-2022, 02:06 PM

13. 
    chainsaw liked post by stug On thread : .308 bush pig load workup

    My bush pig is an Interarms Mark X with a .308. barrel cut to 16”. I think. It has a Gunworks suppressor. My initial load was a 125 accubond with H335 powder. I used H335 because I had it left over...

    Liked On: 08-05-2022, 09:59 PM

14. 
    chainsaw liked post by Ryan_Songhurst On thread : Gun Porn, show off your new toys

    Kimber Classic Select Limited Edition, 6.5cm, Swaro Z3 3-10, bang on 3kg. Happy days :) 196326 196327

    Liked On: 06-05-2022, 09:49 PM

15. 
    chainsaw liked post by stug On thread : Wallaby & stuff

    Nice one, you must have had heavy packs carrying all the ammo around.

    Liked On: 06-05-2022, 08:49 PM

Page 85 of 278 First ... 357172737475767778798081828384858687888990919293949596979899135185 ... Last

• Jump to page: