ChrisW
Member

820 Likes

Page 6 of 55 First 1234567891011121314151617181920 ... Last

• Jump to page:

1. 
   Tedz50 liked post by ChrisW On thread : Big bore Red dot and recoil

   Iv seen low quality red dots not hold zero on a .22 And iv seen high quality red dots purposely be thrown on concrete and hold zero. If its a genuine Aimpoint or similar you are having issues with...

   Liked On: 07-07-2022, 04:12 PM

2. 
   veitnamcam liked post by ChrisW On thread : Burn rate / velocity / pressure / accuracy

   You will have to do load development again. I would start with the same COAL that worked with the other powder and go from there. You could try to aim for a similar velocity and see if it works out,...

   Liked On: 01-07-2022, 08:49 PM

3. 
   dannyb liked post by ChrisW On thread : Burn rate / velocity / pressure / accuracy

   You will have to do load development again. I would start with the same COAL that worked with the other powder and go from there. You could try to aim for a similar velocity and see if it works out,...

   Liked On: 01-07-2022, 11:29 AM

4. 
   Moa Hunter liked post by ChrisW On thread : Burn rate / velocity / pressure / accuracy

   You will have to do load development again. I would start with the same COAL that worked with the other powder and go from there. You could try to aim for a similar velocity and see if it works out,...

   Liked On: 01-07-2022, 11:00 AM

5. 
   NZ_noddy liked post by ChrisW On thread : Drop Chart and Ballistic Solver Sign Conventions

   I guess this is why shooting can be considered a bit of an art. At some distances, and in some wind conditions, you can account for everything, yet environmental variances can be enough that you...

   Liked On: 15-06-2022, 06:11 PM

6. 
   jakewire liked post by ChrisW On thread : Walnut and blued steel,

   I hope you dont mind, but here are some more photos of the sako .22 With such a nice piece of wood and a factory finish being what it is, I decided to refine it a little bit. I applied a few coats...

   Liked On: 04-06-2022, 02:26 PM

7. 
   Mooseman liked post by ChrisW On thread : Dented projectiles

   Sounds like the neck tension may be too tight if it was crushing the case shoulder while trying to seat the projectile. Would also explain the mark on the top of the projectile if too much force was...

   Liked On: 02-06-2022, 07:08 PM

8. 
   7.62 liked post by ChrisW On thread : 6mm Creedmoor vs 243

   A couple years ago, I probably would have went with the CM. Nowadays id probably go with the .243. I just think availability is worth something. I think at distances where there is a real...

   Liked On: 18-05-2022, 10:53 PM

9. 
   Shearer liked post by ChrisW On thread : 6mm Creedmoor vs 243

   A couple years ago, I probably would have went with the CM. Nowadays id probably go with the .243. I just think availability is worth something. I think at distances where there is a real...

   Liked On: 18-05-2022, 06:51 PM

10. 
    Shadowsol liked post by ChrisW On thread : Bushnell's 'BS' Warranties

    Maybe try contacting Bushnell international. Often manufacturers will direct local agents to come to the party to help protect their brand.

    Liked On: 22-04-2022, 06:40 AM

11. 
    caberslash liked post by ChrisW On thread : Bushnell's 'BS' Warranties

    Maybe try contacting Bushnell international. Often manufacturers will direct local agents to come to the party to help protect their brand.

    Liked On: 21-04-2022, 07:29 PM

12. 
    jakewire liked post by ChrisW On thread : Bushnell's 'BS' Warranties

    Maybe try contacting Bushnell international. Often manufacturers will direct local agents to come to the party to help protect their brand.

    Liked On: 21-04-2022, 05:59 PM

13. 
    tetawa liked post by ChrisW On thread : Bushnell's 'BS' Warranties

    Maybe try contacting Bushnell international. Often manufacturers will direct local agents to come to the party to help protect their brand.

    Liked On: 21-04-2022, 02:51 PM

14. 
    Hermitage liked post by ChrisW On thread : Bushnell's 'BS' Warranties

    Maybe try contacting Bushnell international. Often manufacturers will direct local agents to come to the party to help protect their brand.

    Liked On: 21-04-2022, 02:02 PM

15. 
    veitnamcam liked post by ChrisW On thread : Do we get any after-sale service ?

    Hey guys, correct, iv moved on to other things. Iv still got a bit of knowledge though about how the process generally works. What exactly is the problem with it? You didn't specify. I may still...

    Liked On: 26-03-2022, 08:31 PM

Page 6 of 55 First 1234567891011121314151617181920 ... Last

• Jump to page: