csmiffy
Member

3653 Likes

Page 33 of 244 First ... 192021222324252627282930313233343536373839404142434445464783133 ... Last

• Jump to page:

1. 
   csmiffy liked post by akaroa1 On thread : Refurbing a couple of oldies

   I would strongly advise the original poster to put those two emotionally important rifles aside and consider working on a less significant project first. You seem to be coming from a low skill...

   Liked On: 02-06-2024, 01:22 PM

2. 
   csmiffy liked post by garyp On thread : Refurbing a couple of oldies

   Have done up a number of these rifles and have a lot of parts. Small pachmayr pads fit them beautifully. PM me if you need any help. One thing I really like is to look out for low Leupold Sako rings,...

   Liked On: 02-06-2024, 01:22 PM

3. 
   csmiffy liked post by 308 On thread : Colfo Announce Firearms Registry Review

   Agreed The way to sell the abandoning of the register to Joe and Jane citizen is a) Showing how much money it will cost b) Showing how little crime it will solve c) Show how many times overseas...

   Liked On: 02-06-2024, 01:20 PM

4. 
   csmiffy liked post by Southcity On thread : Refurbing a couple of oldies

   The key is think before you launch into anything. Getting some advice has been a great start. One warning is if you decided to use a paint or vanish stripper and either rifle has white plastic...

   Liked On: 02-06-2024, 09:30 AM

5. 
   csmiffy liked post by No.3 On thread : Useing the firearms register

   Often that reason is entirely unrelated to you though - you just happen to be the poor prick that wears the attitude download.

   Liked On: 01-06-2024, 10:07 AM

6. 
   csmiffy liked post by Sidetrack On thread : P14 mag follower

   In someways, I’d really like to replace the stock. It’s had a lot of wood removed from the forend and I’m sure from the butt as well. Also, quite a bit ground off the front of the grip which meant I...

   Liked On: 29-05-2024, 03:09 PM

7. 
   csmiffy liked post by Roarless20 On thread : 223 on deer

   A few yearling fallow with the 75gr eld-m 2920fps. My daughters first deer hunt. She shot her first deer. A yearling hind @25m in the trees after waiting for 5min patiently for a clear shot. It was...

   Liked On: 28-05-2024, 06:07 PM

8. 
   csmiffy liked post by makka On thread : 5.6x57 single shot project

   Next step was to mill a slot for the extractor and test fit it. 251216 That was all good so milled the old extractor off and tig'd this one in place. Also drilled and tapped the shotgun barrel...

   Liked On: 27-05-2024, 10:05 PM

9. 
   csmiffy liked post by BOPR93 On thread : Walnut and blued steel,

   Picked this up this last month, Blaser k95 in 243 Was bought off a real gentleman who has had some bad luck with his health, as the story goes he ordered a quite standard k95, he was known to the...

   Liked On: 27-05-2024, 09:59 PM

10. 
    csmiffy liked post by JohnDuxbury On thread : 270 preferred projectile weight

    130 grain Hornady Interlock at 3100 fps will do anything you ever wanted from a .270 in a hunting rifle.

    Liked On: 26-05-2024, 12:51 PM

11. 
    csmiffy liked post by JohnDuxbury On thread : Husqvarna .30-06

    Thanks for that, very useful. Guess what you get when you check with the powder manufacturer. You're getting their favourite loads in an individual rifle. Off the internet.

    Liked On: 26-05-2024, 12:46 PM

12. 
    csmiffy liked post by Sidetrack On thread : P14 mag follower

    Update on the old girl. Just back from the gunsmith to rectify the scope mount issues. I’d noticed the rear mount was canted off to one side, the alignment was off and the front mount had a broken...

    Liked On: 25-05-2024, 07:55 PM

13. 
    csmiffy liked post by ROKTOY On thread : The next knife

    You have pretty much dawn Jack the Knife, made by Nga. It must be the right design... https://www.nzhuntingandshooting.co.nz/f13/nz-made-knife-jack-45178/

    Liked On: 23-05-2024, 10:50 AM

14. 
    csmiffy liked post by akaroa1 On thread : 3 shot groups are useless!

    I'm guessing those atributes were sub moa 10 shot groups And a relative who gave it to him cheap / free with said sub moa load data

    Liked On: 22-05-2024, 08:36 PM

15. 
    csmiffy liked post by No.3 On thread : Imported trailers, yay or nay ?

    And just make sure that they have NZ standard wheel bearings and seals so you can replace them quickly at WoF fail time. Otherwise they are a pain in the arse and you end up having to hold a couple...

    Liked On: 17-05-2024, 08:51 PM

Page 33 of 244 First ... 192021222324252627282930313233343536373839404142434445464783133 ... Last

• Jump to page: