dannyb
Unapologetic gun slut

13288 Likes

Page 345 of 886 First ... 245295331332333334335336337338339340341342343344345346347348349350351352353354355356357358359395445845 ... Last

• Jump to page:

1. 
   dannyb liked post by veitnamcam On thread : Powder choices for 300PRC

   There is a ship milling about off Auckland as we type waiting to dock with a shipment of powder.

   Liked On: 08-02-2022, 07:41 PM

2. 
   dannyb liked post by andyanimal31 On thread : 30-06

   Knowing what l know now as have a short 308 a medium 3006 and in my past life a 300wsm. A no brainer to go 300wsm in my book for what you describe. 155 amax 800yds and still doing the job on...

   Liked On: 08-02-2022, 06:11 PM

3. 
   dannyb liked post by Kelton On thread : Anyone have a Sako S20?

   won't it depend on action size?

   Liked On: 08-02-2022, 04:04 PM

4. 
   dannyb liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Yeah bit confusing, they have Mac 1 and Mach 2 but I think Strelok does all the calcs if you plug in the nominal BC? I'll test out to 600y and see where I get to.

   Liked On: 08-02-2022, 01:46 PM

5. 
   dannyb liked post by Beaker On thread : Dinner thread?

   So found a packet of risotto rice I brought a few months ago, and decided it was time to have a crack. I don't know why I was hesitant at trying a risotto, easy as! Butter and oil, onion in. Slow...

   Liked On: 07-02-2022, 09:37 PM

6. 
   dannyb liked post by Spudattack On thread : Now here's a question......

   Just give them an extra grain or two of powder, then you can just count the ejector marks[emoji106][emoji23] Sent from my iPhone using Tapatalk

   Liked On: 06-02-2022, 08:25 PM

7. 
   dannyb liked post by 7mmsaum On thread : Notched case - should I use it?

   You have asked a quick question to be on the safe side Wisdom would dictate that any damage to any brass case would see you put that one to one side, crush it and put it in your recycling bin. ...

   Liked On: 06-02-2022, 07:51 PM

8. 
   dannyb liked post by grandpamac On thread : Notched case - should I use it?

   Greetings @ mopheadrob, I wouldn't use it, just to be safe. The notch results in one point on the case head that is slightly weaker. This likely has little effect at normal pressures but could cause...

   Liked On: 06-02-2022, 07:51 PM

9. 
   dannyb liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   COAL adjusted to 3.340" for mag fit. Unlike 3.380", which is not mag fit. FFS. 58.4gn (0.5 MOA first shot cold clean barrel to left) and 58.8gn shot well. Going to try 59.0gn to see if group comes...

   Liked On: 06-02-2022, 04:52 PM

10. 
    dannyb liked post by mikee On thread : 30-06

    True, after shooting my Mates Kimber Mountain Ascent or Sub Alpine (I cant remember which) ....................30/06 I brought a 300WSM and shortened the barrel to 20 inches. I was looking for 30/06...

    Liked On: 06-02-2022, 12:23 PM

11. 
    dannyb liked post by jakewire On thread : 30-06

    I've heard it said that the 30 06 is never a mistake.

    Liked On: 06-02-2022, 11:20 AM

12. 
    dannyb liked post by buell984 On thread : tight closing the bolt

    FLS die, and i didnt have it set properly, dannyb supplied a link on youtube that showed correct setting procedure, i tried it and it worked. I certainly appreciated everyone contributing to forum,...

    Liked On: 06-02-2022, 08:44 AM

13. 
    dannyb liked post by Pete_D On thread : Resizing inconsistency - Am I missing something

    What I've learnt is measure everything when setting up the dies, bullet seating or whatever the process is and measure until you are happy to begin reloading. The only measurement I take after that...

    Liked On: 06-02-2022, 07:53 AM

14. 
    dannyb liked post by Bos On thread : Resizing inconsistency - Am I missing something

    Sometimes I think that a 2 to 3 thou inconsistency in measurements is largely unavoidable. Given the machinery involved and the the measuring devices we use. I've experienced the same "flyers" with...

    Liked On: 06-02-2022, 07:53 AM

15. 
    dannyb liked post by Tikka7mm08 On thread : Resizing inconsistency - Am I missing something

    ^ +1

    Liked On: 06-02-2022, 07:52 AM

Page 345 of 886 First ... 245295331332333334335336337338339340341342343344345346347348349350351352353354355356357358359395445845 ... Last

• Jump to page: