dannyb
Unapologetic gun slut

13262 Likes

Page 8 of 885 First 1234567891011121314151617181920212258108508 ... Last

• Jump to page:

1. 
   dannyb liked post by BRADS On thread : gunworks or dpt?

   https://d347awuzx0kdse.cloudfront.net/nzammo/content-file/ASE%20R&R%20Suppressor%20TEST.pdf Sent from my SM-S916B using Tapatalk

   Liked On: 01-09-2024, 08:07 PM

2. 
   dannyb liked post by 7mmsaum On thread : 243 on deer

   258390

   Liked On: 01-09-2024, 06:47 PM

3. 
   dannyb liked post by akaroa1 On thread : Resurrecting a 159 Year old 44 Rimfire

   These cases are rimfire reloadable Drill trough the primer pocket 5mm Tap it M6x1 Screw in an M6 machine screw Solder it in Cut it off and mill the case base flush Drill, ream and rebate to...

   Liked On: 01-09-2024, 03:56 PM

4. 
   dannyb liked post by Husky1600#2 On thread : NZHS Hunter Challenge and Long Range Day - 7/8 Sept; Sparrowhawk

   The track is a good shingled track, lots of traction. But can be slippery with a fresh shower of rain. Its a decent climb but i've seen plenty of cars go over on a dry day. If you have any doubts...

   Liked On: 01-09-2024, 11:44 AM

5. 
   dannyb liked post by tim37 On thread : last deer, maybe ?

   decided to take Mazy the dog out for one last hunt, she now has bad arthritis in both front wrist joints and a dodgy hip as well. loaded the truck up Thursday night and headed up the Awatere...

   Liked On: 31-08-2024, 10:18 PM

6. 
   dannyb liked post by Hermitage On thread : A question for the doubters

   That's a saying that gets thrown around a lot within the gun community but I've always found it somewhat amusing because there are no serious shooters that have only one gun. Guns are tools, you...

   Liked On: 31-08-2024, 09:58 PM

7. 
   dannyb liked post by Billbob On thread : Euro mounts / skull cleaning

   Just a before and after. 258283

   Liked On: 31-08-2024, 06:36 PM

8. 
   dannyb liked post by SmokeyJason On thread : 300PRC hunting loads, who's using what?

   Ok then some over here in Oz. Just mentioned them as their BC is better than Barnes.

   Liked On: 31-08-2024, 05:21 PM

9. 
   dannyb liked post by Happy Jack On thread : Scrap rimu projects

   Having some scraps of recycled Rimu I decided not to chuck them in the fire but make something. So here is my ammo box that holds 15 rounds (the scraps were not big enough to make a 20 round box). It...

   Liked On: 31-08-2024, 02:26 PM

10. 
    dannyb liked post by Blackfern On thread : Frankford universal bullet seater die

    if you are using Hornady dies you could bet the micrometer seating adjuster and while development of the load happening tinker away and once the load if finalized set the std seater to length. the...

    Liked On: 31-08-2024, 09:39 AM

11. 
    dannyb liked post by Tahr On thread : 300PRC hunting loads, who's using what?

    Yes

    Liked On: 31-08-2024, 09:38 AM

12. 
    dannyb liked post by Stocky On thread : NZHS Hunter Challenge and Long Range Day - 7/8 Sept; Sparrowhawk

    I plan to suck anyway. Need to set s baseline you know

    Liked On: 31-08-2024, 08:40 AM

13. 
    dannyb liked post by Kelton On thread : 300PRC hunting loads, who's using what?

    Iv got an itch that needs scratching Danny so if you go the hammer way il jump in and we will split shipping

    Liked On: 31-08-2024, 08:36 AM

14. 
    dannyb liked post by Bobba On thread : Frankford universal bullet seater die

    Definitely a want more than a need. My issue is I like to tinker and like having a couple of different loads for each rifle. Also starting to load for a few mates so theres more playing around.

    Liked On: 31-08-2024, 08:33 AM

15. 
    dannyb liked post by Kelton On thread : 300PRC hunting loads, who's using what?

    I think Barnes is a little ambitious with their minimum velocity’s, even something in the 180s if you were tempted with monos hammers seem easier accuracy to mate had very good luck with 210 and 215...

    Liked On: 31-08-2024, 08:10 AM

Page 8 of 885 First 1234567891011121314151617181920212258108508 ... Last

• Jump to page: