dogmatix
Member

2194 Likes

Page 45 of 147 First ... 313233343536373839404142434445464748495051525354555657585995145 ... Last

• Jump to page:

1. 
   charliehorse liked post by dogmatix On thread : Starting point for Hornady 68g BTHP

   Just use the 70gn Speer as a a guide. 28gn 2206h Rifle - ADI World Class Powders and Ammunition (http://www.adi-powders.com.au/rifle/22-250-remington)

   Liked On: 24-06-2020, 08:53 PM

2. 
   Spudattack liked post by dogmatix On thread : Gun Porn, show off your new toys

   45-70 levers are the new black.... :D

   Liked On: 13-06-2020, 10:48 PM

3. 
   res liked post by dogmatix On thread : Gun Porn, show off your new toys

   45-70 levers are the new black.... :D

   Liked On: 11-06-2020, 11:43 AM

4. 
   Mooseman liked post by dogmatix On thread : .300 WSM brass flowing

   Also depends if you are neck sizing or full length sizing. Full sizing works the brass should and neck more. You will notice it needs trimming more, especially if there is excessive headspace.

   Liked On: 10-06-2020, 08:49 PM

5. 
   Fawls liked post by dogmatix On thread : Gun Porn, show off your new toys

   45-70 levers are the new black.... :D

   Liked On: 10-06-2020, 06:54 PM

6. 
   Blair liked post by dogmatix On thread : 300 win mag

   Quite a mild 75.5gn of ADI 2217. As I've gone for accuracy and brass life over stonking velocity. Using PPU (Privi/Highland) brass and CCI Magnum primers.

   Liked On: 10-06-2020, 06:52 PM

7. 
   Solo liked post by dogmatix On thread : Gun Porn, show off your new toys

   45-70 levers are the new black.... :D

   Liked On: 10-06-2020, 05:26 PM

8. 
   Blair liked post by dogmatix On thread : 300 win mag

   What I've done for the 300WM loads for a Sako A7, is to have 180gn SSTs to fit the mag for general hunting within 300-350m. As the A7 has a stupidly short magazine. Even factory 180gn soft points are...

   Liked On: 10-06-2020, 03:08 PM

9. 
   mimms2 liked post by dogmatix On thread : 300 win mag

   What I've done for the 300WM loads for a Sako A7, is to have 180gn SSTs to fit the mag for general hunting within 300-350m. As the A7 has a stupidly short magazine. Even factory 180gn soft points are...

   Liked On: 10-06-2020, 02:22 PM

10. 
    A330driver liked post by dogmatix On thread : Gun Porn, show off your new toys

    45-70 levers are the new black.... :D

    Liked On: 10-06-2020, 11:41 AM

11. 
    NZ32 liked post by dogmatix On thread : Howa 1500 223 Internal mag issue

    I have a spare .223 mag spacer if required, as I run detachable mags in mine.

    Liked On: 10-06-2020, 09:26 AM

12. 
    timattalon liked post by dogmatix On thread : Howa 1500 223 Internal mag issue

    But yes, there should be a spacer in the internal factory drop plate mag.

    Liked On: 09-06-2020, 11:37 PM

13. 
    Danny liked post by dogmatix On thread : 303 Ammo

    As others mention, S&B and Privi stuff is easy to get and wont break the bank, ie $45-$50 a box. Federal (blue box) will usually be around the $65-70 mark.... so ouch.

    Liked On: 04-06-2020, 11:11 AM

14. 
    kiwi-adam liked post by dogmatix On thread : 6.5 grendel load data

    I can’t speak from experience with that projectile personally. I’ve previously used the old AMaxes in a number of other calibres for hunting and had good (if spectacular and bloody) results.

    Liked On: 26-05-2020, 02:49 PM

15. 
    Mathias liked post by dogmatix On thread : 6.5 grendel load data

    123gn SSTs or ELDs are the go to projectiles for the Grendel.

    Liked On: 25-05-2020, 08:26 PM

Page 45 of 147 First ... 313233343536373839404142434445464748495051525354555657585995145 ... Last

• Jump to page: