Edunn
Member

118 Likes

Page 4 of 8 First 12345678 Last

• Jump to page:

1. 
   Edunn liked post by Hunty1 On thread : Snorkels (For trucks, not diving)

   Went thru this a while back, places in Dunedin that quoted to fit a snorkel where Midway motors and St Kilda Automotive (ironman 4x4 agent). Didn't end up using either as ended upgrading to a truck...

   Liked On: 30-06-2020, 12:45 PM

2. 
   Edunn liked post by Spitfire On thread : 7mm Rem Mag Troubles

   Sorry - just saw this. I use a patch on an old bronze brush with Autosol soaked in. 20-30 strokes through the throat and a few through the rest of the barrel. I do that after a really good clean...

   Liked On: 04-06-2020, 03:04 PM

3. 
   Edunn liked post by stug On thread : 7mm Rem Mag Troubles

   My cleaning regime for my 7mm mag was use Slip 2000 Carbon Killer to remove the carbon, patch that out then use Boretech eliminator to remove copper. Patch that out, then one patch with oil, then one...

   Liked On: 27-05-2020, 09:34 PM

4. 
   Edunn liked post by grandpamac On thread : Funky speeds - Riddle me this

   Greetings All, The mention of H335 reminded me of a quote about it in one of the old Handloader magazines. It goes. "H335 is like the little girl with the little curl in the middle of her...

   Liked On: 11-05-2020, 06:48 PM

5. 
   Edunn liked post by R93 On thread : Funky speeds - Riddle me this

   Pretty much what pommy said[emoji106] Sent from my SM-G975F using Tapatalk

   Liked On: 11-05-2020, 04:50 PM

6. 
   Edunn liked post by Pommy On thread : Funky speeds - Riddle me this

   Set your dies up for minimal shoulder bump. Don't mix headstamps. Keep them in batches that have had the same number of firings. Clean the lube out of the inside of the cases after you've resized...

   Liked On: 11-05-2020, 01:39 PM

7. 
   Edunn liked post by Cooper On thread : Pressure Differences - ELD-M and ELD-X

   Currently going through the same thing with trying to find accurate loads for a different bullet in my 7mm Mag and know how easy it is to get caught up in the hunt for speed. I would back it down...

   Liked On: 04-05-2020, 01:03 PM

8. 
   Edunn liked post by On thread : These primers OK?

   yep you can put them in a 708 case to try them give you barrel a clean after as well

   Liked On: 29-04-2020, 11:32 PM

9. 
   Edunn liked post by Wildman On thread : Blue Mountains

   Look forward to the report! Sent from my F5321 using Tapatalk

   Liked On: 23-04-2020, 09:20 PM

10. 
    Edunn liked post by JoshC On thread : Blue Mountains

    Heaps of deer mate.

    Liked On: 23-04-2020, 08:57 PM

11. 
    Edunn liked post by skyflyhigh On thread : Blue Mountains

    Come across quite a few deer carcasses up there since the drop , must been poisoned cause the pigs not touching them , but still plenty of them around . Sent from my SM-G960F using Tapatalk

    Liked On: 23-04-2020, 07:41 PM

12. 
    Edunn liked post by Dama dama On thread : Blue Mountains

    Deer repellent used so no likely to have impacted deer numbers to any noticeable degree. If u are really concerned, go for the western blocks or Beaumont end where no 1080 used. If u get a permit,...

    Liked On: 23-04-2020, 07:03 PM

13. 
    Edunn liked post by Dama dama On thread : SI forum chrony

    Looks like I have it booked after Edunn.

    Liked On: 22-04-2020, 04:01 PM

14. 
    Edunn liked post by Rated M for Magnum On thread : Pressure Differences - ELD-M and ELD-X

    I know it's a pain, but I would start from scratch. They are different bullets after all. I've shot both in my rem mag, started with the ELD-M and now use the ELDX. The powder charge for the...

    Liked On: 19-04-2020, 08:20 PM

15. 
    Edunn liked post by Cooper On thread : Pressure Differences - ELD-M and ELD-X

    I have played around with both in 162gr and the ELD-X is a longer bullet which will reduce useable case capacity(increasing pressure) when seated at the same length. The ELD-X also has a shorter...

    Liked On: 19-04-2020, 03:50 PM

Page 4 of 8 First 12345678 Last

• Jump to page: