F Majeur
Member

34 Likes

Page 2 of 3 First 123 Last

• Jump to page:

1. 
   F Majeur liked post by Ryan_Songhurst On thread : Bruce Rifle Club?

   They're probably right to be wary of newcomers...

   Liked On: 23-12-2024, 03:46 PM

2. 
   F Majeur liked post by John Duxbury On thread : Bruce Rifle Club?

   As you can see from the reply above, they don't like new people. They won't get back to you.

   Liked On: 23-12-2024, 03:46 PM

3. 
   F Majeur liked post by gimp On thread : Bruce Rifle Club?

   fernleaf

   Liked On: 23-12-2024, 03:45 PM

4. 
   F Majeur liked post by Marty Henry On thread : Bruce Rifle Club?

   The club was named and vilified by the last government and police during the pogrom and pr fest following march the 15th. That is history but for those involved at the time it would have been...

   Liked On: 23-12-2024, 03:45 PM

5. 
   F Majeur liked post by Snowgrass On thread : Bruce Rifle Club?

   BRC was very close to being closed down so going incognito for a while was a fair choice considering the harassment that Tommygun mentions. Most of which non-members won’t be aware of. Trust is hard...

   Liked On: 23-12-2024, 03:45 PM

6. 
   F Majeur liked post by fernleaf On thread : Bruce Rifle Club?

   The info on the NRANZ website is very (pre-2019) old and no longer valid. If you know a BRC Member, you are welcome to attend as their Guest. If no one from the Club knows you, you will have to...

   Liked On: 23-12-2024, 03:29 PM

7. 
   F Majeur liked post by earplay On thread : CDS/Chrono Question

   As already mentioned - box velocity minus 150fps (assuming 25fps/inch loss) puts you at 2529. Add a few fps for the suppressor, and you're sitting in line with your chrono data, which should be...

   Liked On: 22-12-2024, 08:04 AM

8. 
   F Majeur liked post by gimp On thread : CDS/Chrono Question

   How far do you wish to shoot? That will dictate your requirements.

   Liked On: 22-12-2024, 08:04 AM

9. 
   F Majeur liked post by Bagheera On thread : CDS/Chrono Question

   You can always go back to your MOA cap if you radically change your cartridge. Meanwhile, a dial calibrated in metres is easy to use, foolproof under pressure and as accurate as most people need,

   Liked On: 22-12-2024, 08:04 AM

10. 
    F Majeur liked post by Mararoa On thread : CDS/Chrono Question

    Why get a cds dial? Why not leave the Moa dial on top, work out your drops with a ballistic program and verify them on paper and then write them in the side of your rangefinder on a piece of tape....

    Liked On: 22-12-2024, 08:04 AM

11. 
    F Majeur liked post by zeropak On thread : CDS/Chrono Question

    what you experienced pretty much lines up with what I find in my rifles. The clean bore shot always has a slightly lower velocity. If I sight in prior to going on a hunt I leave the barrel alone,...

    Liked On: 22-12-2024, 08:04 AM

12. 
    F Majeur liked post by Bagheera On thread : CDS/Chrono Question

    Good on you presenting the barrel cleaning history before that session. Question is how consistent you can ever be in future ? Predicting a velocity increase between cleanings is a rabbit hole....

    Liked On: 22-12-2024, 08:04 AM

13. 
    F Majeur liked post by jono7 On thread : CDS/Chrono Question

    Chrono’s are great for gaining fairly accurate(but certainly not always) velocity information that trajectories can be calculated from, but as Yesmate has said, info really should be validated at...

    Liked On: 22-12-2024, 08:04 AM

14. 
    F Majeur liked post by Yesmate On thread : CDS/Chrono Question

    id take the average but also id check the average drop at 400 with a 5 shot group and check that against your fps to confirm that your cds turret will be accurate.

    Liked On: 22-12-2024, 08:04 AM

15. 
    F Majeur liked post by grandpamac On thread : CDS/Chrono Question

    Greetings F Majeur, Many years ago when scope adjustments were less reliable than today I got around the need to dial my scope on a .308 for target shooting by tinkering with the powder charge....

    Liked On: 22-12-2024, 08:04 AM

Page 2 of 3 First 123 Last

• Jump to page: