G.I_Joel
Member

174 Likes

Page 1 of 12 123456789101112 Last

• Jump to page:

1. 
   G.I_Joel liked post by Pete82 On thread : Looking for stalking buddies

   Hey team, was a while since I wrote anything on forums, used to be at old FishHunt forum which no longer exist. Got a stalking-apprentice dog (GSPxViszla) and looking to find guys who have...

   Liked On: 27-02-2025, 09:33 AM

2. 
   G.I_Joel liked post by AlwaysLearning On thread : I did it!

   Hi all! Excuse the enthusiasm! But I am so freaking proud of myself! I have no husband or father to hunt with (I have a wife who is not interested in the slightest).. grew up on a farm shooting...

   Liked On: 27-02-2025, 09:30 AM

3. 
   G.I_Joel liked post by Northlandnewbie On thread : .308 reloading starting point

   I’ve got access to all the equipment and it’s around 60% to reload plus time spent obviously. Aim here is to run a better projectile at same/better speeds with less SD while saving a bit if possible....

   Liked On: 25-02-2025, 08:08 PM

4. 
   G.I_Joel liked post by Fatberg On thread : To many oldies and to few young people.

   Wanted to say thanks to Rushy for this kind offer. I got in touch a couple months back, and after the club's committee approved me to come along, I went to my first club shoot yesterday. It happened...

   Liked On: 06-11-2024, 11:11 PM

5. 
   G.I_Joel liked post by STC On thread : 308

   I stopped following that guy when he recommended the lee beam scale as the most precise means of weighing a load... Apart from that its mostly woffle... Most if not all 308 bullets will be...

   Liked On: 07-01-2024, 07:09 PM

6. 
   G.I_Joel liked post by Frogfeatures On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

   Nice Yammie :thumbsup: In about 3–4 months, when my cancer rates hit remission based on current numbers, I’m buying this little angel Already got signoff from the CEO, and checking out trackdays....

   Liked On: 17-05-2023, 08:06 PM

7. 
   G.I_Joel liked post by Black Rabbit On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

   some bikes of mine, not good ones but good memories. 224041224042224043

   Liked On: 17-05-2023, 08:04 PM

8. 
   G.I_Joel liked post by marky123 On thread : New sp-01 grips

   217411 3d printers rule

   Liked On: 27-02-2023, 10:08 PM

9. 
   G.I_Joel liked post by Ozzy On thread : Help - moving to standard

   If by extended you mean the regular wide safetys, most holsters I have seen have a cut out for them.

   Liked On: 27-02-2023, 01:33 PM

10. 
    G.I_Joel liked post by nzfubz On thread : Help - moving to standard

    I'll ask around at CPC this weekend for you

    Liked On: 22-02-2023, 09:55 PM

11. 
    G.I_Joel liked post by dale On thread : Final results of my bull tahr.

    Have it back now and still goes over 13. So all is well and looks good on the wall. 210292210294

    Liked On: 06-01-2023, 11:24 AM

12. 
    G.I_Joel liked post by johnd On thread : Trouble with scales

    Another tip with beams is to not leave it "on balance" i always take the beam out of its pivot. Just so it doesnt wear excessively...... mostly it sits on the shelf these days but always there for a...

    Liked On: 06-01-2023, 11:22 AM

13. 
    G.I_Joel liked post by gundoc On thread : Trouble with scales

    The beam has a knife edge axle that sits in ceramic vee blocks. A build-up of dust there can cause problems. Once cleaned, your scales should live under a dust cover when not being used.

    Liked On: 06-01-2023, 11:22 AM

14. 
    G.I_Joel liked post by Oldbloke On thread : Trouble with scales

    I had a set of Redding scales that were becoming a little less reliable. The following gave me excellent results. Using a small artists paint brush, remove all dust. Clean the V and brush on some...

    Liked On: 06-01-2023, 11:22 AM

15. 
    G.I_Joel liked post by Husky1600 On thread : Trouble with scales

    I had a similar problem a while ago, had a look and the axle was ever so slightly out of square on one side. Carefully straightened it with a pair of pliers and back to being responsive and accurate....

    Liked On: 06-01-2023, 11:22 AM

Page 1 of 12 123456789101112 Last

• Jump to page: