gqhoon
Member

307 Likes

Page 1 of 21 123456789101112131415 ... Last

• Jump to page:

1. 
   Seventenths liked post by gqhoon On thread : 6mm Creedmoor conundrum

   I ran 6CM on a Tikka action for 1 barrel, and got 2300 rounds on it. Had to really look after it towards the end, and it was probably really done at 1800. ELD’s go well, but Berger 105 Hybrids go way...

   Liked On: 06-04-2025, 08:47 PM

2. 
   Rock river arms hunter liked post by gqhoon On thread : 20ga steel loads

   In addition to the Federal 2 3/4” load, Winchester Drylock SuperSteel in 2 3/4” is another good one to try. Same 1425fps velocity, 3/4 ounce etc.

   Liked On: 25-03-2025, 09:38 AM

3. 
   AMOSK93 liked post by gqhoon On thread : 2 Barrels, 1 Rifle

   gqhoon true, what brand barrels do you have? [/QUOTE] Bartleins and Kriegers. KiwiGreg on here did all the gunsmithing. POI of any barrel would always be within 0.1Mils of where it shot...

   Liked On: 13-03-2025, 07:11 PM

4. 
   AMOSK93 liked post by gqhoon On thread : 2 Barrels, 1 Rifle

   Have got a 6CM and a 223 barrel for my Tikka. It’s not a big deal to swap barrels over, but it you definitely want a quality scope that tracks well so you can adjust your zero easily and repeatedly....

   Liked On: 13-03-2025, 09:06 AM

5. 
   caberslash liked post by gqhoon On thread : The new cartridge that makes the most sense to me.

   Plus freebore length doesn’t suit the higher BC bullets. Often the freebore diameter of those chambers isn’t ideal either.

   Liked On: 09-03-2025, 09:35 PM

6. 
   outdoorlad liked post by gqhoon On thread : Zero targets nz, are they legit?

   He’s a PRS shooter, based in the South Island. He’s legit.

   Liked On: 09-02-2025, 04:42 PM

7. 
   Muttonguts liked post by gqhoon On thread : Carbon fibre stock help

   PM me your address and I’ll send you a spare Gunworks recoil lug I have.

   Liked On: 22-01-2025, 07:59 PM

8. 
   caberslash liked post by gqhoon On thread : White River Primers - Any misfire issues?

   Measure primer height. Measure primer pocket depth. Seat primer to ensure the anvil is bottomed-out on the base of the pocket. WRE are known to be a little bigger in diameter than most, so are a...

   Liked On: 15-08-2024, 01:47 AM

9. 
   Trout liked post by gqhoon On thread : White River Primers - Any misfire issues?

   Measure primer height. Measure primer pocket depth. Seat primer to ensure the anvil is bottomed-out on the base of the pocket. WRE are known to be a little bigger in diameter than most, so are a...

   Liked On: 14-08-2024, 08:00 AM

10. 
    7mil08 liked post by gqhoon On thread : Bore scope?

    I picked up a Teslong wifi unit recently, got it direct from Teslong. About $225 delivered. 174810 174811 174813

    Liked On: 02-08-2024, 07:33 PM

11. 
    Borris liked post by gqhoon On thread : FL resized rounds wont chamber

    Ben, find brass that meets the criteria below 1 - Factory round, pull the projectile and dump powder, confirm it fits in your chamber 2- case fired in your chamber, sized and fits back in your...

    Liked On: 29-07-2024, 10:13 AM

12. 
    19Badger liked post by gqhoon On thread : Seating Depth Test. Waste of Time?

    If they don’t, they lose to someone who does. The actual data is the target.

    Liked On: 25-07-2024, 10:32 PM

13. 
    Sakoswarosorted liked post by gqhoon On thread : Seating Depth Test. Waste of Time?

    5 different matches shot through the course of the day, as environmental conditions vary and then those scores averaged to give an ‘Agg’ is a pretty good sample size. Repeat that for 2 different...

    Liked On: 21-07-2024, 10:38 PM

14. 
    6x47 liked post by gqhoon On thread : Carbon fibre stock help

    PM me your address and I’ll send you a spare Gunworks recoil lug I have.

    Liked On: 12-03-2024, 03:25 PM

15. 
    kiwijames liked post by gqhoon On thread : Carbon fibre stock help

    PM me your address and I’ll send you a spare Gunworks recoil lug I have.

    Liked On: 11-03-2024, 09:47 PM

Page 1 of 21 123456789101112131415 ... Last

• Jump to page: