grandpamac
Member

4715 Likes

Page 29 of 315 First ... 151617181920212223242526272829303132333435363738394041424379129 ... Last

• Jump to page:

1. 
   Nakihunter liked post by grandpamac On thread : Powder options for 7mm08

   Greetings All, I am using AR2206H with the 145 grain projectiles in a 7mm-08 for F-class and it shoots great. AR2206, AR2207, AR2208 and AR2209 were developed in Australia by Mulwex in the early...

   Liked On: 16-07-2024, 10:35 AM

2. 
   Micky Duck liked post by grandpamac On thread : Tikka T3 .270 COL reading .005" off standard COL

   Greetings, Personally I would not put Loctite anywhere near a rifles chamber, just asking for trouble in my opinion. The other problem with the close on chamber method is that with full length sized...

   Liked On: 14-07-2024, 05:12 PM

3. 
   T.FOYE liked post by grandpamac On thread : Tight chamber and marks on projectile

   Greetings, Looks as though the projectiles are seated too long. The marks are from the rifling. Either the adjustment on your die has moved or if you have just started a new box of projectiles then...

   Liked On: 13-07-2024, 09:10 AM

4. 
   Micky Duck liked post by grandpamac On thread : 100 yrs old and still going strong

   Greetings Lucky and all, The turret on top adjusts for elevation and windage is adjusted in the rear base. The scope will be reticle moving so the cross hairs could be above or below the centre of...

   Liked On: 12-07-2024, 10:10 PM

5. 
   Nakihunter liked post by grandpamac On thread : Powder options for 7mm08

   Greetings. I chronographed 41 grains of AR2206H with the 145 grain Speer at 2,800 fps in Lapua cases and a 26 inch barrel. Also 41.5 grains of AR2208 with the 150 grain Remington at 2,570 fps in R-P...

   Liked On: 11-07-2024, 01:29 PM

6. 
   Nakihunter liked post by grandpamac On thread : Fire forming 270 to 280ai

   The .280 and AI cases have longer headspace than the .270 so the correct way is to neck the cases up to .30-06 and then set the shoulder back to a hard close in the .280 AI die. You have missed that...

   Liked On: 11-07-2024, 01:24 PM

7. 
   Micky Duck liked post by grandpamac On thread : Hybrid vs petrol - surprising outcome

   I thought you were taking your mother in law surfing for a bit until I realised you meant serf. GPM.

   Liked On: 10-07-2024, 05:55 PM

8. 
   Woody liked post by grandpamac On thread : Tight chamber and marks on projectile

   Greetings Again, Reading through this post I spotted that accuracy had gone sour with factory loads as well indicating an issue with the rifle as well as the loads so a check of the usual suspects,...

   Liked On: 10-07-2024, 01:10 PM

9. 
   onlyhsh liked post by grandpamac On thread : Tight chamber and marks on projectile

   Greetings Again, Reading through this post I spotted that accuracy had gone sour with factory loads as well indicating an issue with the rifle as well as the loads so a check of the usual suspects,...

   Liked On: 09-07-2024, 10:06 PM

10. 
    6mm08 liked post by grandpamac On thread : Tight chamber and marks on projectile

    Greetings, Looks as though the projectiles are seated too long. The marks are from the rifling. Either the adjustment on your die has moved or if you have just started a new box of projectiles then...

    Liked On: 09-07-2024, 08:43 PM

11. 
    Deanohit liked post by grandpamac On thread : Hybrid vs petrol - surprising outcome

    Greetings all, The hybrid vehicles are likely close to the end of their run. I had spotted that they don't save much in fuel. Plug in hybrid vehicles are a little better but you still have to...

    Liked On: 09-07-2024, 08:07 PM

12. 
    Micky Duck liked post by grandpamac On thread : Tight chamber and marks on projectile

    Greetings Again, Reading through this post I spotted that accuracy had gone sour with factory loads as well indicating an issue with the rifle as well as the loads so a check of the usual suspects,...

    Liked On: 09-07-2024, 08:00 PM

13. 
    Oldbloke liked post by grandpamac On thread : Tight chamber and marks on projectile

    Greetings, Looks as though the projectiles are seated too long. The marks are from the rifling. Either the adjustment on your die has moved or if you have just started a new box of projectiles then...

    Liked On: 09-07-2024, 03:46 PM

14. 
    onlyhsh liked post by grandpamac On thread : Tight chamber and marks on projectile

    Greetings, Looks as though the projectiles are seated too long. The marks are from the rifling. Either the adjustment on your die has moved or if you have just started a new box of projectiles then...

    Liked On: 09-07-2024, 03:03 PM

15. 
    Dazzh liked post by grandpamac On thread : Tight chamber and marks on projectile

    Greetings, Looks as though the projectiles are seated too long. The marks are from the rifling. Either the adjustment on your die has moved or if you have just started a new box of projectiles then...

    Liked On: 09-07-2024, 12:24 AM

Page 29 of 315 First ... 151617181920212223242526272829303132333435363738394041424379129 ... Last

• Jump to page: