Grubby
Member

22 Likes

Page 1 of 2 12 Last

• Jump to page:

1. 
   Grubby liked post by gundoc On thread : Headspace

   That is measuring from the leed to face of the bolt, which is not headspace. Headspace is measured with gauges that measure from a point specified on the shoulder of the chamber (that point varies...

   Liked On: 08-11-2017, 08:29 AM

2. 
   Grubby liked post by Walker On thread : Headspace

   What you are actually measuring is the seating deapth for the bullets. This differs between rifles as chamber reamers wear during use in manufacturing and rounds fired over the rifles life. One rifle...

   Liked On: 08-11-2017, 08:29 AM

3. 
   Grubby liked post by 40mm On thread : Show us your reloading bench

   every time it gets cleaned, it gets messy. 78369

   Liked On: 06-11-2017, 10:48 PM

4. 
   Grubby liked post by R93 On thread : What little pesties did you bowl over today?

   Had a nice evening last night on the underground chickens with the K hornet. Fired 8 shots for 7 bunnies. Tried for one at 285yrds and missed. Using some 40gr Blitzkings that I got with the...

   Liked On: 27-10-2017, 04:51 PM

5. 
   Grubby liked post by Dermastor On thread : Show us your reloading bench

   My wife is just back from the USA and among other goodies brought back a 2nd Chargemaster and dies for the new rifle project. I am a lucky little reloader with the best wife in the world. 76235

   Liked On: 26-09-2017, 05:05 PM

6. 
   Grubby liked post by Gibo On thread : tikka t3 action in a t3 stock?

   Just have to x your fingers on the way in ;)

   Liked On: 14-09-2017, 10:53 PM

7. 
   Grubby liked post by rambo-6mmrem On thread : tikka t3 action in a t3 stock?

   Yep as others said the t3 x is a improved version of the t3 it is the same but with a few little improvements But as far as I know stocks are the same

   Liked On: 14-09-2017, 10:53 PM

8. 
   Grubby liked post by Happy On thread : tikka t3 action in a t3 stock?

   Trigger guard on later models has two little plastic indexing pins. Some of the older ones don't have the holes for those to go into. I ve always just cut them off with no problems

   Liked On: 14-09-2017, 10:53 PM

9. 
   Grubby liked post by mawzer308 On thread : More 270 Win Loads

   They still do and for good reason, they work.

   Liked On: 09-09-2017, 08:41 PM

10. 
    Grubby liked post by septic On thread : reloading .270 with 140g nosler balistic tip

    Gibo would you mind sending me a Pm with your notes, I picked up a new to me .270 stainless fluted Tikka Hunter. I tried some initial loads 49-53 gn 2209 and 140gn SST's. I got great group with 53gn...

    Liked On: 14-08-2016, 10:07 AM

11. 
    Grubby liked post by johnd On thread : reloading .270 with 140g nosler balistic tip

    140 sst's 56 grn AR 2213 2785 fps sub MOA

    Liked On: 14-08-2016, 10:07 AM

12. 
    Grubby liked post by septic On thread : reloading .270 with 140g nosler balistic tip

    53 gr of 2209 turned out to be the ducks nutz in my T3 and my mates A-bolt. Went up to 55 gr, without any pressure signs out of Remington and Hornady brass, but it boots a bit much for me. His old...

    Liked On: 14-08-2016, 10:07 AM

13. 
    Grubby liked post by tikka On thread : reloading .270 with 140g nosler balistic tip

    I had great results with 140gr ABs and 140gr SSTs same POI. ADI 2213sc 57 gr @ 2850fps in a 21" barrel Win brass Fed primers I only run 150gr LRABs now as it has better long range performance.

    Liked On: 30-07-2016, 10:41 PM

14. 
    Grubby liked post by TeRei On thread : reloading .270 with 140g nosler balistic tip

    Loading a mates with 110 TTSX Barnes and 2213sc. Slaying them. Really happy. Had loaded up 130 TSX but this is his new super load.

    Liked On: 29-07-2016, 11:37 PM

15. 
    Grubby liked post by Dicko On thread : reloading .270 with 140g nosler balistic tip

    RE 22 @58 gas behind a 140 balistic tip gives a bit over 2900 fps in my 700 with good accuracy. Sent from my iPhone using Tapatalk

    Liked On: 29-07-2016, 11:37 PM

Page 1 of 2 12 Last

• Jump to page: