gundoc
Member

3978 Likes

Page 186 of 266 First ... 86136172173174175176177178179180181182183184185186187188189190191192193194195196197198199200236 ... Last

• Jump to page:

1. 
   Harryg liked post by gundoc On thread : How to start gunsmithing

   I see you are in Southland which is not too far from me. Give me a PM and you can come and visit and I can give you some pointers.

   Liked On: 19-05-2019, 12:00 PM

2. 
   Max Headroom liked post by gundoc On thread : How to start gunsmithing

   I see you are in Southland which is not too far from me. Give me a PM and you can come and visit and I can give you some pointers.

   Liked On: 19-05-2019, 11:31 AM

3. 
   nzfubz liked post by gundoc On thread : How to start gunsmithing

   I see you are in Southland which is not too far from me. Give me a PM and you can come and visit and I can give you some pointers.

   Liked On: 19-05-2019, 11:14 AM

4. 
   kidmac42 liked post by gundoc On thread : How to start gunsmithing

   It is very important that you get some basic engineering training. High school or polytech is a good grounding, a part-time gopher in a precision engineering shop is also very good. Learn the...

   Liked On: 19-05-2019, 11:13 AM

5. 
   timattalon liked post by gundoc On thread : How to start gunsmithing

   It is very important that you get some basic engineering training. High school or polytech is a good grounding, a part-time gopher in a precision engineering shop is also very good. Learn the...

   Liked On: 19-05-2019, 11:10 AM

6. 
   jakewire liked post by gundoc On thread : How to start gunsmithing

   I see you are in Southland which is not too far from me. Give me a PM and you can come and visit and I can give you some pointers.

   Liked On: 19-05-2019, 11:06 AM

7. 
   Reprosniffer liked post by gundoc On thread : How to start gunsmithing

   It is very important that you get some basic engineering training. High school or polytech is a good grounding, a part-time gopher in a precision engineering shop is also very good. Learn the...

   Liked On: 19-05-2019, 10:56 AM

8. 
   GWH liked post by gundoc On thread : Old pistol, ornament or ?

   Yes, it is worth a maximum of about $200-250 in its present condition. There are a few things counting against it; spurious manufacture, ostensibly Belgian but the proof mark is not correct (should...

   Liked On: 14-05-2019, 06:18 PM

9. 
   chainsaw liked post by gundoc On thread : Remington accuracy

   I have seen quite a few Remingtons in recent years with the chamber misaligned with the bore. The problem is quite obvious visually when the bolt is removed and the front of the chamber examined in...

   Liked On: 13-05-2019, 10:58 AM

10. 
    Tech liked post by gundoc On thread : I am in a state of utter befuddlement

    Brass dippers are the best thing for black powder. Fired cartridge cases are perfect - just trim them to the correct length to give you the desired charge, and solder on a 3" length of brass tubing...

    Liked On: 12-05-2019, 12:58 AM

11. 
    ebf liked post by gundoc On thread : Offhand

    50-60 metres on rabbits, out to 150 on deer etc. Consistent offhand shooting is a technique that takes time to develop, involving stance, breathing, and trigger control. Ping-pong balls with an air...

    Liked On: 10-05-2019, 08:49 AM

12. 
    Josan liked post by gundoc On thread : Offhand

    50-60 metres on rabbits, out to 150 on deer etc. Consistent offhand shooting is a technique that takes time to develop, involving stance, breathing, and trigger control. Ping-pong balls with an air...

    Liked On: 10-05-2019, 05:06 AM

13. 
    GWH liked post by gundoc On thread : Old pistol, ornament or ?

    Are there any proof marks stamped on it? It appears to be a typical example of a flintlock pocket pistol with spring bayonet that were popular in England in the late 1700's to early 1800's, but it...

    Liked On: 09-05-2019, 11:19 AM

14. 
    timattalon liked post by gundoc On thread : 303 conversion to 7.62x39

    I have done a couple of the conversions over the years. The caliber change is the easy part - just set the barrel back about 16mm and recut the chamber. The bolt face, extractor, ejector, and...

    Liked On: 29-04-2019, 08:12 PM

15. 
    baronPolarbear liked post by gundoc On thread : 303 conversion to 7.62x39

    I have done a couple of the conversions over the years. The caliber change is the easy part - just set the barrel back about 16mm and recut the chamber. The bolt face, extractor, ejector, and...

    Liked On: 28-04-2019, 10:29 PM

Page 186 of 266 First ... 86136172173174175176177178179180181182183184185186187188189190191192193194195196197198199200236 ... Last

• Jump to page: