Sometimes rubbish gets trapped in the stock recess below the cartridge lifter. Take the stock off and check, cleaning as required. If you can see marks in the woodwork where the lifter sits when the...
Liked On: 09-03-2024, 08:28 PM
Sometimes rubbish gets trapped in the stock recess below the cartridge lifter. Take the stock off and check, cleaning as required. If you can see marks in the woodwork where the lifter sits when the...
Liked On: 09-03-2024, 08:26 PM
Hold the frame at the bottom of the grip and give the frame (where 02 is written) a sharp rap with the plastic handle end of a large screw driver and the plate will pop up. The same technique works...
Liked On: 09-03-2024, 08:08 PM
The quietest suppressors are the ones with the greatest volume, incorporating an efficient gas-trapping system (eg. close fitting baffles with a recurve face). Volume is the key factor, baffle...
Liked On: 09-03-2024, 12:13 PM
Pretty much! The only accurate readings are done with a properly calibrated decibel meter and then comparative readings of the available range of suppressors done with one firearm, one batch of...
Liked On: 08-03-2024, 12:07 PM
The quietest suppressors are the ones with the greatest volume, incorporating an efficient gas-trapping system (eg. close fitting baffles with a recurve face). Volume is the key factor, baffle...
Liked On: 08-03-2024, 12:06 PM
I started deerstalking with a fully wooded .303 that was my 16th birthday (1963) present from my father, which cost him just under 10 Pounds from Turner & LeBrun for a new FTR'd BSA No.1 Mk.III*....
Liked On: 07-03-2024, 01:44 PM
I started deerstalking with a fully wooded .303 that was my 16th birthday (1963) present from my father, which cost him just under 10 Pounds from Turner & LeBrun for a new FTR'd BSA No.1 Mk.III*....
Liked On: 07-03-2024, 10:33 AM
I started deerstalking with a fully wooded .303 that was my 16th birthday (1963) present from my father, which cost him just under 10 Pounds from Turner & LeBrun for a new FTR'd BSA No.1 Mk.III*....
Liked On: 06-03-2024, 07:54 AM
There are many variables that can affect accuracy, one of which is barrel harmonics. These can vary according to the burning characteristics of the powder. The theoretically correct powder will start...
Liked On: 02-03-2024, 10:59 PM
There are many variables that can affect accuracy, one of which is barrel harmonics. These can vary according to the burning characteristics of the powder. The theoretically correct powder will start...
Liked On: 02-03-2024, 10:47 PM
There are many variables that can affect accuracy, one of which is barrel harmonics. These can vary according to the burning characteristics of the powder. The theoretically correct powder will start...
Liked On: 02-03-2024, 03:19 PM
My old Husqvarna .30 '06 with a 150 bullet at 3,000+ fps will do everything you want it to and then some. My long-range target rifle is good to 1,000+ metres running a 168 grain at 2950 with 2213SC...
Liked On: 01-03-2024, 08:40 PM
My old Husqvarna .30 '06 with a 150 bullet at 3,000+ fps will do everything you want it to and then some. My long-range target rifle is good to 1,000+ metres running a 168 grain at 2950 with 2213SC...
Liked On: 01-03-2024, 04:18 PM
My old Husqvarna .30 '06 with a 150 bullet at 3,000+ fps will do everything you want it to and then some. My long-range target rifle is good to 1,000+ metres running a 168 grain at 2950 with 2213SC...
Liked On: 01-03-2024, 10:09 AM