gundoc
Member

213 Likes

Page 1 of 15 123456789101112131415 Last

• Jump to page:

1. 
   gundoc liked post by akaroa1 On thread : Making Sizer / Reloading dies

   I wanted to have a sizer die / case forming die for one of my vintage rifles so I could run a Nitro for Black load in it. Obsolete Caliber dies are available for the 450 no1 Express BPE from...

   Liked On: 17-03-2025, 10:36 PM

2. 
   gundoc liked post by Southcity On thread : Walnut and blued steel,

   Shifting some guns yesterday and took a better photo of my Winchester 1885 in 220 Swift. 270532

   Liked On: 12-03-2025, 09:52 PM

3. 
   gundoc liked post by akaroa1 On thread : Tiger troubles anyone ? I have the solution

   The buffalo horn fore end tip is dovetailed on to the walnut and then the curved beak is seamlessly fitted up 270240 270241 Which means this shouldn't come loose And there is a small...

   Liked On: 09-03-2025, 09:38 AM

4. 
   gundoc liked post by akaroa1 On thread : Tiger troubles anyone ? I have the solution

   Refitting the case is finished and the Greener looks pretty comfortable in there 270003 270004 270005

   Liked On: 05-03-2025, 11:04 PM

5. 
   gundoc liked post by Nga On thread : Show me your knives

   another one... 268979

   Liked On: 04-03-2025, 10:38 PM

6. 
   gundoc liked post by scotty On thread : 30-06 Freebie!

   yes absolutely some of the bigger recoiling chamberings can catch you out if not positioned and comfortable before the shot 269890 8x57 on the weekend reminded me .....

   Liked On: 04-03-2025, 01:06 PM

7. 
   gundoc liked post by akaroa1 On thread : Tiger troubles anyone ? I have the solution

   So who has a tiger problem ? I now have the solution for you Sadly they are shot out in my current location Happy to travel to the other island Greener 577-500 #2 hammer double rifle ...

   Liked On: 03-03-2025, 08:52 PM

8. 
   gundoc liked post by akaroa1 On thread : Sand Casting. Who's done / doing it ?

   Well I needed two lefts and two rights. So four of these And I needed a Whitworth hammer copied for another percussion rifle project. So I just asked them to cast me 2 left, 2 right and 2...

   Liked On: 07-02-2025, 09:12 PM

9. 
   gundoc liked post by akaroa1 On thread : Sand Casting. Who's done / doing it ?

   Still a lot to do but a bit closer to being at least visually correct 268432

   Liked On: 07-02-2025, 08:19 PM

10. 
    gundoc liked post by akaroa1 On thread : Sand Casting. Who's done / doing it ?

    Finally got my replacement copied investment casting hammers Pretty happy with the quality and price Fitted up on the better of the two double barrel pistols Still have to brown the other...

    Liked On: 07-02-2025, 07:17 PM

11. 
    gundoc liked post by SixtyTen On thread : Building a test fire tube / bullet trap

    Made a start today. I picked up 1.2m of 200x200x9 square hollow section plus had the steel shop plasma cut a 20mm plate for the bottom. I fired up the arc welder and glued the plate to the bottom of...

    Liked On: 08-01-2025, 04:26 PM

12. 
    gundoc liked post by physeptone On thread : Sad Commentary on Life and Balance.

    Surely this is an anomaly in the data. There can't possibly be a link.

    Liked On: 05-01-2025, 03:44 PM

13. 
    gundoc liked post by A330driver On thread : Gun Porn, show off your new toys

    265568265569

    Liked On: 25-12-2024, 10:09 AM

14. 
    gundoc liked post by No good names left On thread : How to immobilise old fiream to create safe wall hanging

    You could always sell half to offset your costs

    Liked On: 21-12-2024, 04:04 PM

15. 
    gundoc liked post by Billymavs On thread : How to immobilise old fiream to create safe wall hanging

    I have been present for a similar process pre 2019 for two No3 mk1* rifles, the requirement was any and all load bearing parts and any moving components must be structurally compromised and...

    Liked On: 20-12-2024, 04:28 PM

Page 1 of 15 123456789101112131415 Last

• Jump to page: