Gur1
Member

16 Likes

Page 1 of 2 12 Last

• Jump to page:

1. 
   Gur1 liked post by Tokoroa Cast Projectiles On thread : 450 Bushmaster bullet mold

   Hi Guys, I have had a few enquiries about cast bullets for the 450BM, I hear there are quite a lot of them in country, my heaviest .452" bullet is 250 grains, I have had a look for bullets designed...

   Liked On: 29-11-2024, 06:04 PM

2. 
   Gur1 liked post by superdiver On thread : First tahr....finally!

   Headed down to a mates in Lake Hawea last weekend for a hunt. After a bit of a drive we parked up and headed in getting ready for my first hunt in almost 6 months so dreading the climb to camp....

   Liked On: 27-10-2024, 06:56 PM

3. 
   Gur1 liked post by 338MAN mk2 On thread : Cast Lead Thread ?

   The big hollow ensures a big hole at subsonic speeds. The mold has 3 nose pins to make a big hollow 330gr, a shallow hollow 350gr and a 360gr flat nose. I think the 350gr cup point shallow hollow...

   Liked On: 11-09-2024, 11:40 PM

4. 
   Gur1 liked post by akaroa1 On thread : Cast Lead Thread ?

   Time for some more cast lead I finally got a mould I've often thought might be useful to have in the mould hoard Lyman 457 330 grain hollow point Gould mould My new old Army & Navy 45-60...

   Liked On: 29-07-2024, 04:12 PM

5. 
   Gur1 liked post by Jhon On thread : 45 Colt Rifle 350-60gn loads

   A little 3x6 incremental load test made up to test tomorrow all going well. 350g (nominal), .352, PC PB FP over Hogdon 800X, 45Colt cases. Shooting in a LSI Rossi Puma 92 454Casull. Projectiles...

   Liked On: 06-06-2024, 03:21 PM

6. 
   Gur1 liked post by Micky Duck On thread : Online data thread???

   hmmmm where did that go?????? was just looking for the trailboss formula bit online and cant find it elsewhere......and then looking at .44 magnum load data online its frustrating as buggery...

   Liked On: 20-07-2022, 08:54 PM

7. 
   Gur1 liked post by T.FOYE On thread : Improving 45-70 ammo with a mandrel

   Found this one just sitting on the clay (the miracle find) That coating is tough eh. Even the rifling didn't remove it 201705 201706

   Liked On: 19-07-2022, 11:59 AM

8. 
   Gur1 liked post by madmaori On thread : Ruahine's hunt

   Hey team , Going for my first wander in the Ruahines (embarrassing considering I have lived in the bay for so long) tomorrow with a mate that is fresh as to hunting and wouldn't mind having a...

   Liked On: 10-07-2022, 07:05 PM

9. 
   Gur1 liked post by Woody On thread : WTB large rifle primers

   Was tking to Custom Cartridges (Taupo) today and he has cci 200 br2 in stock and also some small rifle primers.

   Liked On: 26-03-2022, 05:21 AM

10. 
    Gur1 liked post by BruceY On thread : Ice boxes best and best value

    Hi Akaroa...I bought one from REPCO a 'GEARUP' 25 litres I think on special bout $70 bucks...and I'm bloody pleased with it..as above freeze anything you can and rather than ice packs or salt-ice or...

    Liked On: 09-02-2018, 01:54 PM

11. 
    Gur1 liked post by Shootm On thread : 7mm rem mag convert to smaller cal? advice please...

    You have a 7-08 in the for sale section with a Dpt can. Wouldn't that be the answer to your problem with the rem mag, just using the 7-08 I mean?

    Liked On: 30-01-2018, 08:36 AM

12. 
    Gur1 liked post by EeeBees On thread : Dog Bedding

    Cambo, the 'working dog' ones are standard chaff bag size 112 x 56 ... I cannot remember the name of the wool buyer but it is on the corner of Orchard and Maraekakaho Road opposite the sale yards...

    Liked On: 26-08-2017, 08:17 AM

13. 
    Gur1 liked post by chainsaw On thread : any one running Barnes pills in 7mm

    Aye. Already run partitions as my round of choice for 0-300 yards. They work very well. My interest in Barnes is the solid copper & no lead option ..... and cos I like experimenting and learning.

    Liked On: 15-05-2017, 05:29 PM

14. 
    Gur1 liked post by Cody.a On thread : 308 or 6.5x55

    Thanks Micky duck yeah I'll try tee something up cause I'm just a tad worried about the slight pitting that was mentioned. I had a savage axis 308 and I'm not 100% but I'm bloody sure the axis is...

    Liked On: 03-01-2017, 12:30 PM

15. 
    Gur1 liked post by Rushy On thread : What little pesties did you bowl over today?

    What is wrong with Hoggett Happy? I like Hoggett. Hoggett is wonderful. Hoggett, Hoggett, Hoggett.

    Liked On: 14-10-2016, 08:37 PM

Page 1 of 2 12 Last

• Jump to page: