GWH
Member

4134 Likes

Page 85 of 276 First ... 357172737475767778798081828384858687888990919293949596979899135185 ... Last

• Jump to page:

1. 
   GWH liked post by Uplandstalker On thread : The model 7 in your life

   I've given my Model 7 a rebirth From a 260imp to 6XC in a 1:7.5 26 inch heavy barrel. PT&G detachable bottom metal with MDT steel mag. Gunworks 3 port brake. I've put the original factory...

   Liked On: 16-02-2020, 10:15 PM

2. 
   GWH liked post by cameronjackwhite On thread : The model 7 in your life

   130775 New to me, mod 7 260. Just fitted into a stug stock and its shooting tidy groups with the bergers so far. Weighs 2.9kg all up, one of my favourite rifles to date

   Liked On: 16-02-2020, 10:12 PM

3. 
   GWH liked post by Wingman On thread : Zastava 7.62x39 Restoration

   Yes that is basically where I ended up. 130636 After loading a few 125gr TMKs and finding a load with 2207 over the chrono I found the case formed to the chamber nicely and all slop at the rear...

   Liked On: 15-02-2020, 08:09 AM

4. 
   GWH liked post by Wingman On thread : Zastava 7.62x39 Restoration

   So the MAB barrel blank I selected is a 25" long 4140 CM 1-10" twist light Sako contour in a .308" bore diameter. The profile was a fraction lighter than the Zastava barrel but I am planning to my...

   Liked On: 15-02-2020, 08:09 AM

5. 
   GWH liked post by Wingman On thread : Zastava 7.62x39 Restoration

   Before I got started on the new 7.62x39 barrel I had a .22 grendel itch I had to scratch.. I had a very short trueflite 1-8" twist .223Rem take off barrel that I wanted to test the .22 Grendel...

   Liked On: 15-02-2020, 08:04 AM

6. 
   GWH liked post by Tahr On thread : 150 Eldx in 7mm?

   Yeah. I haven't used ELDX much (one deer) but with the NBT I agree that no matter what happens there is always the solid copper base with rough shards of petal attached that pushes through and causes...

   Liked On: 10-02-2020, 11:55 AM

7. 
   GWH liked post by superdiver On thread : . 284 Winchester

   Will message you as it was a warm load...

   Liked On: 09-02-2020, 10:05 AM

8. 
   GWH liked post by Spitfire On thread : . 284 Winchester

   I ran mine at a very slow but very accurate 2650 fps with 162s and 2213sc. Still killed everything stone dead.

   Liked On: 08-02-2020, 11:45 AM

9. 
   GWH liked post by wsm junkie On thread : . 284 Winchester

   There must be something to these tikka 9.5 twist barrels. This is the results of my dabble with the 180 eldm's in my 7mm08ai Load development 129941 And a group at 600yds with the chosen...

   Liked On: 05-02-2020, 11:30 PM

10. 
    GWH liked post by Nick-D On thread : . 284 Winchester

    Fuck that's impressive speed/ballistics. What twist rate? Standard 1:9.5 tikka? Sent from my CLT-L09 using Tapatalk

    Liked On: 05-02-2020, 10:47 PM

11. 
    GWH liked post by Wingman On thread : Attempting a new .224 wildcat

    I have had a few private messages with questions in regards to this build and how the barrel life etc was holding up so I figured Id do an update here too. The barrel is still going strong...

    Liked On: 05-02-2020, 03:56 PM

12. 
    GWH liked post by Wingman On thread : Attempting a new .224 wildcat

    Just had a quick play with some Hornady Z-Max 40gr and BM 8208.. crazy fast varmint round! 108951 108950 108949

    Liked On: 05-02-2020, 03:52 PM

13. 
    GWH liked post by McNotty On thread : Attempting a new .224 wildcat

    That's going to explode some bunnies!! There's some bloody clever buggers around, awesome to see stuff like this being done.

    Liked On: 05-02-2020, 03:48 PM

14. 
    GWH liked post by Wingman On thread : Attempting a new .224 wildcat

    Finally got s few hours in the workshop to finish my barrel and sized/fire formed a handful of brass for it. 108797 108796 I loaded a few 69gr Sierra TMKs to run some powder tests over the...

    Liked On: 05-02-2020, 03:48 PM

15. 
    GWH liked post by Wingman On thread : Attempting a new .224 wildcat

    Thanks to NZ_noddy for the loan of the 6mmBR die as I have now got the brass sorted for this chamber. I sized a handful of 6.5x47lap brass down to 6mm then to .22. I tested a few in the chamber...

    Liked On: 05-02-2020, 03:46 PM

Page 85 of 276 First ... 357172737475767778798081828384858687888990919293949596979899135185 ... Last

• Jump to page: