Hahn
Member

155 Likes

Page 6 of 11 First 1234567891011 Last

• Jump to page:

1. 
   Eat Meater liked post by Hahn On thread : Torqueing screws for cheapskates

   Don't forget to calculate in the prevailing torque and watch the angle of pull, as well as any wet install torque. :yaeh am not durnk:

   Liked On: 10-10-2022, 05:22 PM

2. 
   rewa liked post by Hahn On thread : rifle change / load/ no bumps etc

   Any damage to the crown or suppressor? That could explain a sudden change if everything else has checked out fine.

   Liked On: 03-10-2022, 09:15 AM

3. 
   nor-west liked post by Hahn On thread : MS_SP Magnetospeed chronograph

   Looked a touch expensive but appears they are going back up in price. Was NZ$350 retail when I got mine. But you can save a few $ here assuming shipping would be similar:...

   Liked On: 03-08-2022, 03:30 PM

4. 
   dannyb liked post by Hahn On thread : MS_SP Magnetospeed chronograph

   They work really well. Some don't like how they affect point of impact being attached to the barrel. Others have come up with ways to mount to the stock to overcome this. Some cut them to use with a...

   Liked On: 03-08-2022, 08:24 AM

5. 
   Micky Duck liked post by Hahn On thread : Low recoil Factory 308 Ammo

   I wonder what accuracy would be like. Assuming they chamber and fire... :o

   Liked On: 03-07-2022, 04:23 PM

6. 
   hotsoup liked post by Hahn On thread : MSR Windburner Cozy fitting

   I couldn't work out why the cozy was so loose so sent an email to MSR. Turns out I'm not that smart and it is operator error. I figured they went to the trouble of making instructions so I'm probably...

   Liked On: 07-05-2022, 10:02 AM

7. 
   Hunty1 liked post by Hahn On thread : MSR Windburner Cozy fitting

   I couldn't work out why the cozy was so loose so sent an email to MSR. Turns out I'm not that smart and it is operator error. I figured they went to the trouble of making instructions so I'm probably...

   Liked On: 06-05-2022, 12:33 PM

8. 
   winaa liked post by Hahn On thread : Magnetospeed sporter on a suppressor

   Ha no iron content in the projectiles... Which means I don't understand how the magnetospeed works :cave: I got my 10x2.5mm at https://amfmagnets.co.nz/ in Aus The manual says you need a 1/8"...

   Liked On: 19-04-2022, 08:59 AM

9. 
   RV1 liked post by Hahn On thread : Cactus Huntaway DIY frame…

   It's a very tight but perfect fit as you can see from the photos, probably slightly tighter than the pack it came out of. Approximate dimensions as best I could measure: 258mm x 495mm x 17mm...

   Liked On: 03-03-2022, 08:39 AM

10. 
    Micky Duck liked post by Hahn On thread : Cactus Huntaway DIY frame…

    It's a very tight but perfect fit as you can see from the photos, probably slightly tighter than the pack it came out of. Approximate dimensions as best I could measure: 258mm x 495mm x 17mm...

    Liked On: 02-03-2022, 08:37 PM

11. 
    Bobba liked post by Hahn On thread : Cactus Huntaway DIY frame…

    It's a very tight but perfect fit as you can see from the photos, probably slightly tighter than the pack it came out of. Approximate dimensions as best I could measure: 258mm x 495mm x 17mm...

    Liked On: 02-03-2022, 08:26 PM

12. 
    rugerman liked post by Hahn On thread : Emptying an underfloor tank

    And any steel farm tank. I have an old 1000L tank, the mechanic in me hates the idea of the rust and water forming inside it, but keeping it full defeats the purpose or having it. Two good quality...

    Liked On: 21-02-2022, 10:43 PM

13. 
    Stump liked post by Hahn On thread : Emptying an underfloor tank

    You'd be surprised how much water is in aircraft fuel tanks, especially in humid climates. A trick I was taught learning about water testing was when you have your bucket of fuel and it looks clean...

    Liked On: 21-02-2022, 05:33 PM

14. 
    norsk liked post by Hahn On thread : Emptying an underfloor tank

    Sounds like you have a good plan. Don't get too carried away though. Once you have emptied the water as much as possible and cleaned up with the meths just keep an eye on your water separator/filter....

    Liked On: 21-02-2022, 12:20 AM

15. 
    planenutz liked post by Hahn On thread : Emptying an underfloor tank

    To be fair you could probably just drain the water and carry on without dropping all the fuel and flushing the tank. Keep a spare filter handy and keep emptying the water bowl.

    Liked On: 20-02-2022, 08:00 PM

Page 6 of 11 First 1234567891011 Last

• Jump to page: